When I tried to recover the CNCZone password, it redirected me to Industry Arena.
After password recovered, I can login to Industry Arena only. Every time I click something linked to CNCZone,...
Type: Posts; User: Jung
When I tried to recover the CNCZone password, it redirected me to Industry Arena.
After password recovered, I can login to Industry Arena only. Every time I click something linked to CNCZone,...
I am CNC service engineer, living in Guelph.
Hi cmpcleveland, What is the fanuc control model?
check the line#127 of diagnostic screen, bit #5 if it is 1.
Can you upload the screen with error?
For alarm 420: It may have loose connector, or mainboard need to be repaired. Check connectors first.
about "no PMC file": how do you know there is no PMC? what is your parameter 905?
WMC usually...
You have to change Pro-Motion parameter. If you have Pro-Motion manuals, send me a copy (I don't have).
Hi Raygun,
My machine turret lost parameter, could you please help me set paramater.
Thanks
Jung
Hi M-man,
When turret servo's battery went out I replaced bat, but now the turret turn 1/10 for 1 tool ( actually it must be 12s). Could you help me fix parameter for this problem?
Machine: puma...
You are awesome! Thank you very much.
Hello,
I have entered almost parameters (from parameter sheets) to Mazak M-Plus H400, but I don't know how to enter PLC I/F parameter.
Does anyone know how to get into this PLC parameter...
hi Kenvin
The number of axes now is only 2 (displayed x and y axis only). I think I have to input option parameters first so that I can input parameter for z axis.
Can I input Option throught...
Hi Kenvin,
It's lucky today. This morning when I try turning on power, the massage "MMON GO UNREADY" did not appear again. I could get into parameter screen but there are lot of garbage in...
Hi Kenvin,
So sad hearing that ! They don't have Yasnac service in my country.
One more question: they did initialize FC200 card at your place or you sent it to them?
Jung
Hi Kenvin,
You are right, I took out FC200 and got problem. Now when power on, the booting screen displayed and then it turned into blank with message "MMON go unready". I cannot manage to get...
hi Kenvin,
Did you solve the "system go unready"?
I got the same problem. Could you please help me?
Jung
hi not an expert: you are expert ;)
hi Hitachi Man,
My Hitachi VK45 (Seicos Mark II) got trouble a couple days ago. All leds on panel is lighted. I think that SLBus table got problem. Could you show me how to check and set SLBus...
hi piston_90,
i got the same problem. Did you find out the solution?
jung
did you find it out? I have a maintenance manual, PM your email
Hi Chippy,
I have done as you said, but I got only System Parameter page. All the other pages (such as machine parameter - about 11 pages) I couldn't get.
Could you please give me some advice...
there is no parameter for "reset to turn off spindle", it depend on machine tool builder that they allow that or not.
to swap M3 and M4, you could look in the magnectic box to see which relay for M3...
Hi,
I'm dealing with lost parameter machine. Parameter list has lost some pages including spindle parameter.
I tried some motor codes but no hope, It away got alarm 13057: SPINDLE PARAMETER...
Hi,
I need to build a special mill machine with only one axis (to move cutting tool). I found in my warehouse some PowerMate model E but ther is no manual (connection, maintenance ...). I have some...
I am apriciated if you could give me SRAM file of both heads of this lathe. Thanks
Timer occupies 2 bytes for preset data, so if your ladder use timer 350, timer preset should be at DGN 350 and 351. Try this: preset time x 20 and convert it to binary and set to 350 and 351. If dgn...
Hi,
I can print ladder from PMC ROM, If you need please PM or email to [email protected]
Usually you should have Tape or DNC position on mode switch on control panel. In DNC mode, diag 127#5 must be 1. This bit could be 1 only when machine uses PMC. If your machine uses PMC (L or M) you...
Check for 121#4 (emergency) on diag screen. It must be 1 for machine ready condition. If it is 0, you can check on ladder screen for G121.4 to see what made this bit 0. You should also check for...
Is machine OM?
Check if machine has decelerate limit switches? You can try to press limit switch and watch on diagnostic screen if 16#5 (x dec. ls), 17#5 (y dec. ls), and 18#5 (z dec. ls) flip flop....
As my experience, just need to turn on 901#6, set PWE=1, and press "read" in edit mode.