Search:

Hi I have a Rofin Baasel lamp pumped Yag laser with Rofin LaserCad
the unit has a problem booting
is there anyone experienced in Rofin Baasel Lasers
thanks Peter

Hi N it seems like the VSd has a problem the cd750 suffer from capacitor deterioration. The PLC will detect the fault and should go into EStop .
If you are in Australia I have a spare VSD if you...

Hi all I am retrofitting a Biesse rover 322
Does anyone have a circuit diagram or service manual
Peter

So far no joy in moving the axis , just cant work out what could be the problem ,
All the servos are energized
peter

We had a CACR .9kw drive go faulty , as we had a spare CACR .5 kw we installed it as a replacement to drive the .9kw motor .

The motor has very little load and it seems to work but can hear its...

Hi Thanks
there are no interlock problems on parm 700 or 701
any other suggestions
Peter

Hi all
I have a .5kw yaskawa CACR servo pack driving a .9kw motor
Does any one know how to change the motor parameters on the servo pack fro .5 kw to .9kw.
i can see the motor parameters but...

Hi I have a Flow pump with mechanical shifting , it intermittently stops shifting.
On the hydraulic shift tubes one side gets hot the other is much cooler

if some one has a flow pump can they...

Hi Tim have eliminated all limit , over travel and home switches on the mill
any other suggestions

We have a leadwell MCV with Fanuc Om controller , The z Axis has had a major tool crash into the bed
Now no Axis will move .
The screen has no fault codes or alarms.
have checked the obvious...

I have problem with a H2o jet 50 hp pump with mechanical cables shift valve and need help
it does not seem to cycle properly , it pumps to 30k psi then after a few seconds pressure drops to 0 and...

I am not familiar with the diagnostic function of the fanuc.
How do I display the PMCDGN data as indicated on the pdf

We have a leadwell MCV with Fanuc Om controller , due to faulty tool offset the z Axis crashed into the bed , we managed to home after the crash but now no Axis will move .screen has no fault codes...

Working servo Drives and Control computer from Meldas CNC ,all drives and controller fully working mill had mechanical spindle problems .
parts include MDS-B-V1-20 , MDS-B-V2-2020 , MDS-B-SP-110 ,...

Hi Roger , Thanks , when I look at the monitor sometimes the characters change like a refresh or a digital process and sometimes they are OK as the monitor is just composite video i dont think its...

Hi I have a Fanuc OM with 9 inch mono monitor , all the monitor characters have vertical lines in front of them , before i get a new monitor any one know if its the monitor or the fanuc computer that...

Hi Does any one have some IR SL3 parts . I am looking for an High pressure cylinder

regards Peter

Hi All , just installed a CNC mill with a Meldas 50 controller

After power up it shows these errors:

M01 operation error 0004
T01 cant cycle st 0104
3043 spindle not orient

could some...

Hi > I have a scanlab digital hurryscan galvo that has a fault with the X axis producing a thick line of approx 1mm , Y axis is OK , it is not the Laser as I have 2 galvos and swapping confirms its...

Hi Dave thanks , even at 22ma it still has the same problem , if I turn off the water pump and leave for about an hour it works ok for a while then after about 5 mins power drops off , cant see how a...

Hi All
I hope you can help
I bought an 80 watt CO2 laser tube and I am having problems and hope you can help.

The tube is brand new but has been boxed waiting for install for 12 months
I...

Hi Chich
thats great , you have now inspired me to finish off my upgrade for the Femco , I have interfaced a 4 axis GSK controller which includes a C axis, its been shelved for a while as I am...

Hi Did you buy the rofin laser , is it a powerline rsy90?
where are you located ?
regards peter

Hi Chris
No Problems . just let me know if they are the same boards
regards Peter

Hi Chich
Hope allis ok , just checking to see if you recieved the pictures and if you are still intersted in the Femco parts
regards peter

Hi Chich , I will sell you the one I have for $900 , the menbrane switch, also includes the monitor spindle drive , power supply , servo drives , cpu , memory card control card mother coard etc ,...

Hi All
If any one is intersted I have a fullset of Fanuc Cards for a Femco lathe including Spindle drive , Dual servo card , power supply CPU series 0/00 control card and memory , screen with touch...

Hi HSD auto change spindle ES919 at 35kg, auto change tool holder with air driven holders and plc electronics wont be expensive but very heavy and would cost a lot to ship from Australia to the UK ,...

Hi All

I have just pensioned off 2 Biesse Rover 346 ATC both were working OK before scrapping them , I have all parts including 5 HSD auto change spindle motors and computers all very cheap , I...

Hi Does any one use mastercam for waterjet cutting , I would like to know how you slow the feedrate for the corners and how do you include fish tails for sharp corners
thanks and regards Peter