I tried that too. It made no diference also tried belt compensation in parameters, no joy. Thanks for trying.
Type: Posts; User: smellyfeet
I tried that too. It made no diference also tried belt compensation in parameters, no joy. Thanks for trying.
gregoryblane G97S1000M03 in MDI gives me 800RPM (CSS off) even after turning off and clearing the memory. Manual mode also only gives me 800RPM.
I tried G50 S2000 no joy. I have been through all the settings in the book and changed a few relating to spindle speed still no joy. No matter what you ask for you alway get exactly 20% less.
Its...
Thanks Jim but unfortunately not that simple.
Hi. Our TL1 has suddenly started running at exactly 80% spindle speed. Eg. Demand 1000 get 800. Any ideas?
Hi, I have a Bridgeport VMC 760 with spindle problems when I start the spindle, it just goes solid.
Can anyone tell me if I spin the spindle by hand should I get a reading on-screen like on the...
Did anyone get to the bottom of this one?
I have the same problem on my 760. When you start the spindle it goes solid but will not rotate.
I get the error only on the first tool change attempt...
Hi.
We have a problem with the lubrication on our VMC600-22 digita in that the oil is not being pumped to the bearings and ball screws. It is getting to the small union under the motor-end cover...
Similar problem here. Did you figure it out? Is there some way to reset all errors.
Thanks.
Hello Fella. Its definitely a 6h thread that is specified on our customers dwg. The Machinarys Handbook does go into some detail about calculating a "h" thread at the bottom of the 6g standard...
Hi. I have just replaced my blown cranial gasket and am ready to try again.
I am trying to figure out how to calculate the 6h tolerance position for a M24 x 1 thread and I cannot get my head...
Hi all...
Does anyone know anything about the Emcoturn 220? There was a turret hang up when it indexed with a too long tool which caught the guard. It blew a chip and cap on the positioning...
Thanks G-Code junki but that was obviously the first thing I did.
The machine would not zero as per the manual so I phoned Citizen and the guy in the service dept told me it was the batteries, so...
Hi,
Does anyone have the procedure for clearing the error " Z70 - Abs posn ref pt set incomplete 0001 Z2 $2"
Thanks.
Hi Mate. Did you fix it?? I just had the same problem on mine turned out to be a loss of the timer information. Try manually actuating the turret by pushing a small allen key into the back of the...
Hi, Have you tried starting the controller while holding P and Cancel then zero return?
Sorry, I have been on paternity leave for a couple of weeks. Thanks for your answers, I have just topped up using water and got the refractometer readings back on the scale (roughly 5%). One thing...
We use Castrol Hysol EP soluable and after a couple of weeks of evaporation and topping up the refractometer reading goes off the scale.
I was told by Castrol and the rep that you shouldnt top off...
Thanks for all your suggestions, I am going to try a modified version of the paddle wheel that will look more like one of those 1970s drinking flamingos.
We are also going to try cork chips.
I...
Hi all,
On night time running, my lathes are reliably churning out parts but that is where it all goes wrong. The parts are falling into a container with either de-watering fluid or water with...
Does anyone have a post-processor for a TL-1 any cam system will do.
Thanks.
Hi,
What was the problem in the end? I am having a prob with my Hurco BMC 20 the post processor I have is driving me crazy as I have to spend ages on the machine editing.
Thanks.
Hi,
Did you have any luck finding one? I need the same thing but I am having a hard time location one.
Thanks.