Search:

Thank you I appreciate it

Thanks anyway the Haas Dealer sent me one

I was wondering if anyone has a model of the Haas TRT100 rotary 5th axis, to use in Onecnc
Thanks

Has anyone modeled up a Haas TRT100 rotary for use in cad/cam, that they would be intrested in sharing
Thanks

Thanks for your help I found the problem, some times when I start the Mill the fuse in the panel blows. I took the cover off to change the fuse and in the process of taking the cover off it turned...

I do not know what a nitrogen counter balance is, I have taken the back panel off and inspected the wiring on the e-stop every thing appears to be fine

My 2013 has VM 3 gave me a emergency stop switch error 2001, I have cycled it multiple times no change, any suggestions.

Does any one know if I can use the same post processor in ver. 7 as I am using in ver. 5
Thanks

Thanks, the machine is new I was just wondering if I needed a bigger compressor.

I just took delivery of a VF2 SS, can any tell me what the cfm is for the air gun thanks

The haas tech was the one that found the problem when he set the machine up. I just got a call from them and they have scheduled a software upgrade for the machine. Hopefully that will take care of...

It does not matter which one I use the result is the same. The problem with using the drill is it centers the tool for checking, which on large dia. end mills could be a problem and it does not spin...

The problem is in the programing of the tool setter if you enter the tool type as end mill and run the process it causes the alarm, if you change the tool type to drill it works fine. Are any of the...

Batteries are good

I have a DT-1 with the wireless probing system, I have not used the machine for a while. When I went to set the offsets on a new tool I get an alarm, which reads probe open can't find anything in the...

So far the machine is working fine, it really hauls on the rapids I have to keep them turned down. I don't think their would be any problem using a 1/2 end mill. the only thing that I did not like...

The specs on the DT-1 call for a 100 amp service, seems like a lot of amps for a 15 hp machine. I am going to use a digtial phase convertor, the one for 20 hp has 64 amps the one for 100 amps is...

4th axis and probe

They changed the price the 1st of the year, I called for a quote for mine on the4th of Jan. the quote came in at the higher price. I checked the web site again and the price was still down, so I...

that is a good point, I was on one of the other forums this morning and they were talking about the fact that Haas uses ceramic bearings in spindles that operate in excess of 12000 rpm. It was also...

Does any one have one of these machines and how do you like it. Mine is supposed to be built next week.

I was wondering if someone knows who makes a drill chuck holder for a tl2 with 4 position turret. I have seen them for quick change tool posts, but not with a .75 inch mount to fit my turret Thanks.

can anyone explain how to change the home position on a tl-2 series lathe, it has a 4 position tool turret I would like to use the tail stock but the tool change location will slam into it if I try...

Thank You for the help the problem was one little check mark in the post prossessor

Okay I did that and the machine added the dia to the tool length when I try and run the part the first cut is the distance of the radius to close to the center line. If I only put in the radius...

I have a new tl2 with a 4 position turret when I set the Xtool offset, I run the tool until it touches the part then I push the x dia measure button which gives me the distance from the center of the...

Thanks I will do some looking

If you do not mind where did you purchase the spindel increaser I have Been for one
thanks

My ver 22 has started putting I J and F axis along with the X Y and Z when I post Im using the haas tm post processor any ideas why?

new to haas tmp-3 does anyone know how to access scaling I have it enabled