Search:

I have already ordered via ebay 48v 10.4A for € 64.68. I already have the same. I will connect 2 CL57T controllers to each, and another CL57T and Leadshine DM556 to the other. For XYZ axis I have...

Unfortunately, the trimmer drops the voltage only to 49.96V.

I found a trimmer on the front panel and will try to lower the tension. I got this power supply years ago for little money. Back then, the prices of power supplies with such power were expensive. I...

Years ago I got a cheap SMC1800-50V-33A power supply. The power supply has an output of 50.5V. My CL57T controllers (3 pieces) are designed for 24-48v.
Will 2.5v more be too much for my controllers?

Maybe someone else is right. On another forum, someone pasted a link to a blog where a laser like mine is described and a link to the software.
LINK
P.S. I forgot to write that I managed to start...

I removed the stepper motor controller. Below the controller is a 15w404as chip. I am interested in which softwear is designed to control stepper motors.
...

I am adding more pictures:
https://shrani.si/t/2y/xA/A1VvQ7S/20210915220000.jpg

https://shrani.si/t/X/e9/AfYJvaW/20210915220008.jpg

https://shrani.si/t/m/rU/crBEs9j/20210915220038.jpg
...

I got a Chinese laser engraving machine from a friend. Since he hasn't had it in use for a long time, he can't find the software. Next to the laser there are also stainless steel plates with the...

I have mach3 R3.043.066 installed on my cnc-powered computer. I have three different profiles to run mach3.
4.axis:.
cnc:
laser:
When I select a provil and run it, a notification appears
***...

Today I uninstalled mach3 and reinstalled it, deleted all profiles and created a new profile, but it still shows me the error as in the picture.

http://shrani.si/t/h/Dg/2LIST4Sg/error.jpg

No, I just copied copies of my profiles that I saved.

When I start and close the mach3 program, a notification is silenced:
xmlnetprofile
load waring- ,hexadecimal value 0x0C,is invalid character. line1 position400

415498

Where should I look...

Today I tested the UC100 USB motion controller connection.
I made four tests, the error does not appear anymore, and the engines do not rush. He works fine for once.

Would using the UC100 USB motion controller solve this problem?

Mach 3 I have installed on win7 32bit. Before 14 days the problem arose, With the axis began to lose the steps. I checked the mechanical circuit cnc, replaced the leading bushings. Mechanical damage...

When creating a milling path, (Z level roughing) for 4 A axis, how to define Z Slices? If I leave Avtomatic, it begins to milling 0.5mm (the material allowance I have set is 0.5mm) above the center...

I made 4 axes for my cnc. I run CNC with mach3 program. I tried to make the G code for the 4th axis in Artcam2008, but I do not know which postprocessor to choose? 4th axis I have X-axis oriented. G...

I installed an additional 10K potentiometer and connected pin1 and pin 2 with a jumper. now I can regulate engine speeds from 6000 to 24000 turns, which I also wanted.
Thank you Mactec54 for help.

Maybe you did not understand me. With the built-in potentiometer I would like to regulate the speed of 7000 to 24000 turns. But I can only regulate from 7200 to 15600 turns. If Pd002 is set to 0 then...

I got a new VFD HY02D223B and attached a 2.2kw water-cooled 400Hz engine. I set the parameters as written above only
I set Pd 02 to 1 because I want to control the plants with a potentiometer that...

Okay. Then I'll get the keys of different colors.
Thank you.

Thanks for the quick answer Mactec54
I have another question. What happens if you press the REW button by mistake when the FWD switch is turned on?

I mounted a 3-button NO on the dashboard. One button for right rotation one for the left and a reset button. I connected the keys to GND, FWD, REV and RST on the control panel of the frequency. In my...

That blue wire on the engine is a wrap of a cable that I protected with a blue thermal shrinkable tube. Thanks mactec54 with your help I started the engine and I can change engine turns.
I set Pn01...

220v

I'll replace the wires. Thanks for the advice. In the evening, when I get out of the job, I'll try it out.

II have a milling machine Bernardo BF25 Top. Since my original electric motor was burnt, I bought a used electric motor of 1.1 kW 2860 turns. I have a frequency regulator ask power 131. I have a...

Then the store is trustworthy.
Thank you.

I would like to process my BF25 top milling machine into CNC. I went to the STEPPERONLINE store where very good prices are available, but also from Germany. I want to get the Leadshine DM556 Stepper...

I have a mounted laser on cnc, which I control with the TTL controller. The laser turns on when the g code is minus (-) and goes out when it goes to the plus (+), so the Z axle motor is also off. So...