Search:

Hi folks:

I have worked along with the lead engineer in Ruida and came up with a new patch for the R6445G. With the new patch (only for the R6445G or our R6 DSP controller),. it should allow you...

Don't get fooled, the CW3000 is NOT a chiller. It is a fake one because there is no AC compressor. If you use it to drive a 80W tube in a garage, the water temperature will rise up to 50'C in...

500Watt Fiber Optics Metal Cutting Machine
600mmx580mm (2ft x 1.9ft) Cabinet Fiber Laser Metal Cutting Machine

420832

Carbon Steel (mm, Min/min, gas)
1.0 6 O2
1.5 3 O2
2.0 2 O2
3.0 1.5 O2

Hi folks:

We're carrying long last G.S.I CO2 laser tube with power range from 100W, 130W, to 150W. We also have 260W (300W max) double tube available for high speed acrylic or playwood cutting....

I know this post was a little outdated. But see what we have done so far. See our new RTAF (Real time auto focus)
https://www.youtube.com/watch?v=rjhTnPCnJMo

Marco
LightObject

@rinconchuck , are you sure it is RECI 100W tube? The Reci 100W should have length about 1.4M (55.5") as opposite to 1.2M (47.5") which is a 80W tube. But a lot of seller or manufacturer nowaday...

Post the image of your controller and I may be able to tell
Or email me: [email protected]

-Marco
LightObject

What controller card came with your laser machine?

-Marco
Lightobject

Not quite right. If your controller is locked at 75%, it means that the max power is locked to the ceiling, 75%. If you set 'layer' power to 95%, the power will be limited to 75%. By the way, make...

Thank you Cgeber we, that was exactly I wanted to say. We have no problem to support our products anytime. We listed many fundamental questions and answer in our support forum and we always referred...

Non existent support? Not even consider 13 times replying through emails as support? It is not our job to to help a customer to find out the pin definition of their own controller board. We support...

HI folks

I'm going to LA to serve a couple laser machines from 9-22 to 9-24. If you are in Southern Cal and need laser services (upgrade, repair, tune up), let me know and I'll come to assist you...

We used SPT 850mm 40W for our PR530 machine. The power supply is our own 40W PWM laser power supply that you can find it in our website LightObject
Next thing I'm going to do is to do rotary...

Just did quick anodized(black) test on our PR530 laser machine.

http://www.youtube.com/watch?v=keVZWhvvh1o

I didn't use high speed but 400mm/s. Power is 11% and scan gap is 0.05

Stove doesn't need FDA approval but a laser does! LoL
Stove doesn't burn you if you don't touch it but laser burn you even you just look at it
Stove burned is recoverable but retina burned is...

I think you didn't get the point of my post. What most important I tried to bring up was that using green laser and blue is dangerous without caution. To know where the blue or green came from is...

No big deal to make an apology when made a mistake. And it is a good altitude and no shame to admit a mistake. We are all human and we made mistake. :stickpoke

It may not be 'true blue' but closed to UV. But the green laser is coming out from 808nm though thats what the manufacturer in China told me about it.
I did find an article here:...

If I were you guys, I will not tangle around with this kind of laser! It is very dangerous due to the unique wavelength spectrum that a beam reflection may burn your retina without proper google...

Hi folks:

Marco from LightObject! Just want to let you guys know that a new shipment just arrived our warehouse in Sacramento, California

List:
Laser tube:
10x RECI 130W laser tube
10x...

If you want to engrave fine text through a CO2 laser, you may want to use a 38.1mm focus lens instead of the most popular (default) lens that come with a laser machine from China which is 50.8mm....

It is normal for Reci 100W or 130W. For those tube, it need 8~10mA to get fully activated mode (stable). If you drive the tube with less than 8mA, the beam is not stable and not solid. Plus, the beam...

Hello WolverineX:

Thank you for selecting us as your laser supplier. I'm glad that things went well and the tube arrived saftely. BTW, please do NOT use soldering iron trying to wire the HV to the...

You may want to give a try on our DSP upgrade package. For sure the K40 can do nice cutting on 3mm plywood. No doubt about it. I was doing upgrade for one of my customer two years ago and I was able...

Update:

Shipment has passed US Custom check and released by FDA. Pending for unload from the ship at the Oakland. Most likely that the shipment arrive our warehouse on coming Monday!

I'm going...

No, it is not the hardware is totally different even though it looks similiar. See attached images. I used to carry both card (I name it 2011 DSP and 2012 AWC608) but there is hardware issue on the...