510,116 active members
3,958 visitors online
Register for free
Login

Search:

Type: Posts; User: mdynac

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    37

    Re: Charmilles Roboform 4LC Spark Eroder

    hi

    that machine is actually a Chmer brand machine with Charmilles name on it.
    Contact EDM Network
    they can get you a manual
  2. Re: Charmilles Robofil 200 -- need help diagnosing

    message me your contact info and i can help you out.
    michael
  3. Replies
    3
    Views
    147

    Re: Charmilles robofil 4020.0 lost reference

    check your NC rack voltages. set 5 volts to 5.1 vdc measured at the backplane!!!!!!


    check and replace your batteries on the UA+SAL board.

    check your 24 vdc supply.

    thats a start
  4. Re: Charmilles Robofil 400 Generator Chain failure Diagnostics listed.

    hi

    E02 P01? is a 24 vdc failure usually.......

    i can repair UP/UPH boards if you can t-shoot it down to that

    mac
  5. Replies
    4
    Views
    269

    Re: Cost effective Wire EDM recommendation?

    Talk to Larry McNamee at edmsupport.com. he can assist you with all the details of the 90's Agie wires, he has parts and an excellent service tech to support those machines.


    Sent from my Torque...
  6. Replies
    3
    Views
    2,894

    make sure that both the upper and lower contact...

    make sure that both the upper and lower contact wetting waters are flowing.
    also i would remove both upper and lower injection chambers and service them.
    while the chambers are removed switch...
  7. Replies
    1
    Views
    232

    find the source of the short and remove it. ...

    find the source of the short and remove it.

    the table should not move while in short.

    check the wire feed for shorts, etc.

    good luck,
    mac
  8. are you using CT-EXPERT to create tech? Or are...

    are you using CT-EXPERT to create tech?

    Or are you using predefined tech?

    is this a "Brass" generator?

    try :

    B 7.3
  9. Replies
    25
    Views
    8,949

    no i don't have any schematics for the weir. ...

    no i don't have any schematics for the weir.

    for a replacement, use:
    5 Volts DC at 60 amps
    plus/minus 12vdc or 15vdc at live 5 amps each should do.

    good luck
    mac
  10. Thread: roboform c axis

    by mdynac
    Replies
    2
    Views
    428

    i can fix that board. pm me for more info..... ...

    i can fix that board.
    pm me for more info.....

    michael
  11. Replies
    1
    Views
    1,298

    call EDMNetwork.

    call EDMNetwork.
  12. Thread: PCB Repair

    by mdynac
    Replies
    1
    Views
    705

    i've been repairing all edm pcb's for 17 years....

    i've been repairing all edm pcb's for 17 years. done boatloads of japax and sodick, charmilles, mits, ona, you name it.

    mac
  13. well you are not really EDMing when the machine...

    well you are not really EDMing when the machine is in dry run, you are probably(definately) making contact between the wire and the work. so you have turned the machine into an eletronic bandsaw.
    ...
  14. Replies
    1
    Views
    457

    hello Carlos, is it a console2 ??? mac

    hello Carlos,

    is it a console2 ???

    mac
  15. Replies
    25
    Views
    8,949

    hello yssvaff, "E05 P07" usually means a bad...

    hello yssvaff,


    "E05 P07" usually means a bad power supply.

    check for green led's on the UA/SAL circuit board. (no red leds lit just after power up.)

    check your 24 vdc power supply.
    check...
  16. Replies
    1
    Views
    236

    thats an old machine. it runs on a pdp8\a...

    thats an old machine.

    it runs on a pdp8\a computer.
    it loads software by tape, but it can store g code in memory.
    hopefully they have a tape reader eliminator card installed.
    it burns quite...
  17. Replies
    18
    Views
    1,071

    you should read the info supplied above and you...

    you should read the info supplied above and you will see that the your ON time is WAY too long and your OFF time is WAY too short.

    what about your wirefeed system and wire tension BOTH must be...
  18. Replies
    18
    Views
    1,071

    that would work but it would be a crude spark. ...

    that would work
    but it would be a crude spark.

    AT&T also offers Rotary Phone service.......


    mac
  19. Replies
    18
    Views
    1,071

    PULSE RATE (frequency) adjustment may be a...

    PULSE RATE (frequency) adjustment may be a problem with the sinker gen.
    usually there is no provision for that as they adjust OFF time instead.
    the pulse rates should be variable from approx. 5Khz...
  20. Replies
    18
    Views
    1,071

    i agree with jetski. your going to have to...

    i agree with jetski.
    your going to have to examine the output pulses of that sinker genrator.

    a wire machine's generator output is not quite the same as
    a sinker generator.
    the "ON" times...
  21. Replies
    1
    Views
    390

    call edm network EDM Machine | Electronic...

    call edm network

    EDM Machine | Electronic Discharge Machines | CHMER EDM | Sinker | Wire | Sodick | Used | Tooling | EDM Network

    they can hook you up with a resonable and reliable used edm
    ...
  22. Replies
    4
    Views
    883

    i've worked on many SH2's and i don't recall the...

    i've worked on many SH2's and i don't recall the machine automatically homing on power up, thats just not part of the Sodick boot sequence......
    i should be able to help you.
    PM me for contact info...
  23. Replies
    1
    Views
    562

    take a high resolution photo of the board and...

    take a high resolution photo of the board and email them to me and i'll tell you if i can repair it or not. the photos must be clear and focused in order for it to be useful
    reply here and i'll give...
  24. Replies
    16
    Views
    1,288

    then have one made, its like 1600 bucks

    then have one made, its like 1600 bucks
  25. Replies
    16
    Views
    1,288

    i get mine from digikey Digi-Key -...

    i get mine from digikey

    Digi-Key - MP6-3E-1L-1L-00-ND (Manufacturer - MP6-3E-1L-1L-00)
Results 1 to 25 of 102
Page 1 of 5 1 2 3 4