508,132 active members
3,012 visitors online
Register for free
Login

Search:

Type: Posts; User: ZASto

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds; generated 40 minute(s) ago.

  1. Replies
    14
    Views
    79

    Re: My CNC has gone CRAZY please help

    Welll.. yes, 3 750W AC servos on 3020 :D :D
  2. Replies
    14
    Views
    79

    Re: My CNC has gone CRAZY please help

    @cncmakers001: Would you put AC servos on a flimsy 3020 made in PRC?
  3. Re: Newbie question - how to attach two part 5500mw laser module to generic 3018 Pro

    As far as I can see on your photo, on the red connector there are Pins for Power (+12V), Laser Power Control (PWM), and I recon, Common (GND).
    You should provide power to the module through +12V/GND...
  4. Re: Newbie question - how to attach two part 5500mw laser module to generic 3018 Pro

    So, where are your pictures?
  5. Re: 3018 Woodpecker CNC >> Initial setup troubles

    You should read this:
    https://github.com/gnea/grbl/wiki/Grbl-v1.1-Configuration
  6. Replies
    2
    Views
    47

    Re: Mach 3-4 recommendations

    Did you check official Mach3/4 site?

    https://www.machsupport.com/
  7. Re: Telecaster Body CAD: Looking For Someone To Make Modifications

    Ok, this is Tele body with pickguard overlay.
    You will have to find dimensions of bridge and pot/switch plate.
  8. Thread: 6040 Chinese cnc

    by ZASto
    Replies
    7
    Views
    91

    Re: 6040 Chinese cnc

    Nice to hear :)
  9. Thread: 6040 Chinese cnc

    by ZASto
    Replies
    7
    Views
    91

    Re: 6040 Chinese cnc

    OK, your controller is NOT an USB controller. It is standard controller that accepts Step/Dir signals from PARALLEL port.
    You need some software that sends these signals over the printer port....
  10. Thread: 6040 Chinese cnc

    by ZASto
    Replies
    7
    Views
    91

    Re: 6040 Chinese cnc

    Which interface do you have (USB -> Parallel)?
    You have to be aware that using Chinese USB controllers can be problematic with Mach3, which, BTW, ceased in development 6 years ago.
    I just obtained...
  11. Thread: How old are you?

    by ZASto
    Replies
    424
    Views
    1,533

    Poll: Re: How old are you?

    I'm just enough :)
  12. Replies
    5
    Views
    50

    Re: New Spindle drive Boxford V190 VMC

    Have you cheched datashet of your spindle drive? Page 30.

    http://www.lenze.org.ua/pdf/530_Speed_controllers_1202_EN.pdf
  13. Re: Upgrading from Steppers to Hybrid Steppers (servos) questions

    Math is more than correct,
    600mm/sec = 36000mm/min = 1417,322834646in/min
    800mm/sec = 48000mm/min = 1889,763779528in/min

    Anyway it is very fast 36 or 48 m/min
  14. Replies
    3
    Views
    53

    Re: X and Y axis not 90 degrees

    How did you check squareness of your gantry?

    Did you made test firing at the 4 extreme corners of gantry travel and measure diagonals?
    In the attached picture you can see the representation of...
  15. Replies
    6
    Views
    63

    Re: Stepper drivers to the arduino

    Well, even maxed out, it works like a charm.

    Anyway, nice to see that to hear from developper.
  16. Replies
    6
    Views
    63

    Re: Stepper drivers to the arduino

    For what it can do Uno/Nano is quite capable to run a machine.
    If you are inclined to programming, you can use Mega to add extra functionality (if you posses programming skills)

    Long time ago I...
  17. Replies
    25
    Views
    223

    Re: NCStudio OR Controller

    If you have a laptop that is from era of Methusalem, then you might be out of luck that it has autodetect possibility.

    Any decent laptop will autodetect the cable type.

    BTW Bentley is overkill...
  18. Replies
    6
    Views
    63

    Re: Stepper drivers to the arduino

    Bare in mind that your drivers are expecting active LOW signals for Step/Dir/Enable.
    You should check on arduino the active levels for the same signals.
  19. Replies
    25
    Views
    223

    Re: NCStudio OR Controller

    Well...
    Laptop is your friend. A cheap one just for controlling your CNC machine.
    Buy a decent external controller, not cheap chinese, but one that connects with your computer over LAN cable, eg....
  20. Re: Need Vacuum/ spoil board suggestions for small thin alum. Labels!

    Painters tape + cyanoacrilate, perhaps?
  21. Replies
    3
    Views
    99

    Re: Convert vcarvepro file to SVG

    This?

    https://cloud.mail.ru/public/3V7D/38eMuCaTV

    If it works, Simon ows me a Guiness :D
  22. Replies
    2
    Views
    182

    Re: CNC articles translater needed

    You can contact me through private message, interrested for colaboration.
    User manual, russian, looks quite good, haven't read it in full.
  23. Replies
    1
    Views
    45

    Re: OmniTech 1212 trouble

    Y axis: In Config/Ports and Pins - Motor Outputs, reverse Dir low active (if it is ticked untisk it or vice versa)

    You downloaded and installed Mach3 Demo. Limitation is 500 lines of G-code, and...
  24. Replies
    5
    Views
    164

    Re: DSP and spindle rpm from gcode

    You can not "overpower" the spindle.
    Speeds 1 through 8 are programmed in your VFD. Speed selection is via 4 inputs on VFD / outputs from DSP.
  25. Replies
    4
    Views
    126

    Re: Chinese GRBL Board End Limit Switches

    And to add some resistors :)
    Should read the code, it is very well documented/commented.
Results 1 to 25 of 94
Page 1 of 4 1 2 3 4