looking for a Prototrak DNC Key.
Southwestern Industries says they are no longer available.
Part # 16280
thanks
Type: Posts; User: cnctoolman
looking for a Prototrak DNC Key.
Southwestern Industries says they are no longer available.
Part # 16280
thanks
Is there any RECI co2 laser tube reps on the board anymore?
Would like to get intouch with one.
Thanks
I have a Baldor servo motor for sale. Was purchased this year. It is a refurbished one, that I had purchased and have not used. It was going to go on my Journeyman 325 with the Delta 20 control. ...
Was looking into them, Cant find a whole lot of information yet on them, Was wondering, if they were servo models or steppers. Aslo availabilty and size of tool holders.
Ive seen a couple...
Ill have to look into that. So far, havent found much of anything. It will do it sporadically, but doing it more and more.
here in the last week the x-axis has been starting to "run away" and faulting out quite a bit. Have checked axis lag, and all 3 are at .015. What to dianose next?
Have the baldor "big mho"...
Alittle backlash in the "y" so figured since I was doing it, I might aswell do "X". Also chasing a small finish issue in "x" aswell. machining a side cut, go down one way, smooth, go the opposite...
Does anyone know the part numbers for the Thrust Bearings on the X and Y axis? Looking to replace them and would like to have them in hand before I tear into the mill.
thanks for any help
When replacing brushes, do the new ones have a "correct" profile to them, or so they need a wearing in ? Have never done it, on a servo,so asking for reference
Great post. Nice to have all this info for troubleshooting purposes.
Mine ended up being the card. Got s new card from parts and smarts and problem fixed
Well after reinstalling it, axis lag on z is now .0014. And the balance pot will still not make any change. So stumped at the moment
Well I switched cards on the y and the z and the problem switched to the y, so going to do a tune.
What I found with initial tests
Tp1 to r19- 8.3
To tp2 - 0
To tp3 - 7.9
...
Hopefully I can get it figured out. Mine is just on the z-axis. It's stuck at the moment at .0008. Hopefully after a retune, it will get there.
going to try and redo the tune on the z-axis. Have not done it yet before. which plugs are you referrning to with this -NOTE: All plugs must still be disconnected?
following as I just had the same thing happen today. Machine has been running fine and then all of a sudden,z-axis error. Tried adjusting the balance pot and aswell cant get it to .0002 at all. ...
I have a hurricane laser 36x24 co2 laser. I have a job where I need just about an 1/8" more travel on the table cutting. The movement is there, its just in the settings I cant change the table...
job has been place with a vendor on here.
Thanks to all.
a couple emails supplied are bouncing back due to the email addresses, and cant respond to some of the pm's as not able to or inbox's full just to let some know.
looking for a shop that does small lot runs of CNC turning,. Mainly aluminum, some copper. tolerances are not tight at all. nothing tighter than +/- .003. capabilities of milling while in the...
A vendor has been found for this job. Please close the thread
Have prints for 2 different sized aluminum rings. 500 pc lots of each size. 3003 material aluminum. .031 or can be .02. . tolerances are easy. Send a pm and will send prints. Will check back in...
Having a weird issue. Have a J325 with the dynapath 20 controller. When I hit the estop on the mill and leave it sit for a few, when I release the estop, it hits a motor overload. And off course...
just used it a couple of days ago. Went to use it today and no beam. Opened up the back and all the light are on, except on the power supply. I hold in the test button on it, and can get the laser...
Wouldn't it be more beneficial to use servos, or even hybrid steppers?
I would be more apt to look at a Tormach if it used servos as a second op machine.
Job has been awarded out. Thanks to all who put quotes in.
end of April if possible
1.750" +/-.005
1.750" +/-.005
I have solid model available aswell. material to be 6061. The smaller tapped holes are all 6-32 with a 3/8" depth of thread to be clarified. USA based shops only.
If you need the model let me...