584,865 active members*
4,852 visitors online*
Register for free
Login

Search:

Type: Posts; User: Andrey67

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    19
    Views
    2,343

    Re: Micromaster 420 and 2.2kw Chinese spindle

    Thank you!
  2. Replies
    19
    Views
    2,343

    Re: Micromaster 420 and 2.2kw Chinese spindle

    What parameters and pins of the VFD should I use for this?
  3. Replies
    19
    Views
    2,343

    Re: Micromaster 420 and 2.2kw Chinese spindle

    Now I'm using the BOP.
    My CNC is in the process of building only.
    I want:
    ---if the VFD has an error - the servo stop
    ---if any servo has an error - the other servo stop also
  4. Replies
    19
    Views
    2,343

    Re: Micromaster 420 and 2.2kw Chinese spindle

    My English is bad, maybe you did not understand me :).
    I have a homemade CNC machine.
    While the machine was on, the spindle stopped working and the VFD published the error again. If the axises keep...
  5. Replies
    19
    Views
    2,343

    Re: Micromaster 420 and 2.2kw Chinese spindle

    I did so U=Pin 1 V=Pin 2 and W= Pin 3 it works too.
    Should I use P0314=1 P0640=100% P1135 still?

    How can I stop the servo on my CNC if the error is again? Should I break the control power...
  6. Replies
    19
    Views
    2,343

    Re: Micromaster 420 and 2.2kw Chinese spindle

    U=Pin 2 V=Pin 3 W=Pin 1 GND= Pin 4
  7. Replies
    19
    Views
    2,343

    Re: Micromaster 420 and 2.2kw Chinese spindle

    I tried P1080=100 (water cooled) and had the same error.
    There is another similar VFD with the same settings. With the second VFD, I had another error F0001. And this error is not permanent either....
  8. Replies
    19
    Views
    2,343

    Micromaster 420 and 2.2kw Chinese spindle

    I have used the VFD (Micromaster 420 2.2kw) and new 2.2kw Chinese spindle. The VFD was configured as:
    Р0003=1
    Р0004=0
    Р0010=1
    Р0100=0
    Р0304=220V
    Р0305=8A
    Р0307=2,2kw
    Р0310=400Hz
    Р0311=24000
  9. Replies
    61
    Views
    27,820

    Re: High Power UHU Thread (HP.UHU)

    About 30A.
    I have only this label.
    334994
  10. Replies
    114
    Views
    15,005

    Re: USB pendant from Russia

    May be necessary the new firmware after replacement of LCD module. I'm doing a free repair. But you need to send pendant to me.
  11. Replies
    114
    Views
    15,005

    Re: USB pendant from Russia

    I use a thin soldering iron to it.
    I think that the problem in the Chinese LCD module. Necessary to replace it.
  12. Replies
    114
    Views
    15,005

    Re: USB pendant from Russia

    Hello Jan!

    When has appeared this problem? After what actions?
    Check the integrity of solder to each of 37 pin. (Use a magnifying glass.)
    If everything is OK, then try to solder a wire between...
  13. Replies
    61
    Views
    27,820

    Re: High Power UHU Thread (HP.UHU)

    I've been using the UHU HP servo on my mill and it works perfectly!
    But there are new DC servo motors 20Nm 120V and 400V 34A 11kW.
    Is it possible to improve the UHU HP servo for working with...
  14. Replies
    114
    Views
    15,005

    Re: USB pendant from Russia

    I have founded the new budget version - the ShuttleRU_STM32v.2 in plastic case. It differs from the previous version by a smaller display (it was 2.8" and now it is 2,4"), and the number of the...
  15. Replies
    12
    Views
    4,071

    Re: xhc for KMotionCNC

    Hi Eric,

    Is your version of KMotionCNC free? If yes, where can it be downloaded?
  16. Replies
    42
    Views
    13,664

    Re: Andrey's UHU HP

    is this question for me?
    I do not sell the board ever.
  17. Replies
    31
    Views
    8,407

    Re: Panasonic Panaterm Driver Software

    Thank you!
  18. Replies
    31
    Views
    8,407

    Re: Panasonic Panaterm Driver Software

    OK!
    Good luck!

    Regards,
    Andrey
  19. Replies
    31
    Views
    8,407

    Re: Panasonic Panaterm Driver Software

    Hello Gegard,

    I did so for my amplifer model (S-series). After installing the software:
    Open the file Minas-s.def (C:\Program Files\PANATERM\ini\def) via Notepad++ and find this lines ##194,...
  20. Replies
    31
    Views
    8,407

    Re: Panasonic Panaterm Driver Software

    Here.
  21. Replies
    42
    Views
    13,664

    Re: Andrey's UHU HP

    I checked it out and think all the elements are OK.
    Now I will set the Vref again and will control of it more often.

    How to do so: If any axis is stopped (error) Mach3 stop too?

    Regards,...
  22. Replies
    42
    Views
    13,664

    Re: Andrey's UHU HP

    The Vref decreased to 70mV (it was 200mV) for axis Z.
    But why did it happen spontaneously?
    Maybe the reason necessary to look deeper?

    Andrey
  23. Replies
    42
    Views
    13,664

    Re: Andrey's UHU HP

    Hi,
    I have used the UHU HP 6 years without problems!
    But yesterday I had an Error for the axis Z. If I take off the timing belt, the motor turns without problems. A small load leads to an error...
  24. Replies
    114
    Views
    15,005

    Re: USB pendant from Russia

    Write me at: [email protected]
  25. Replies
    18
    Views
    7,196

    Re: AC servo Panasonic and Mach3

    Another question.
    How can I connect 4 servo apmlifiers so if one EMERGENCY stop others stopped too?
    How it should look like in the diagram?
  26. Replies
    18
    Views
    7,196

    Re: AC servo Panasonic and Mach3

    Mactec54

    P46=1
    P4B=1

    Andrey
  27. Replies
    18
    Views
    7,196

    Re: AC servo Panasonic and Mach3

    I found the cause!



    The parameters were:
    P46=10000
    P4B=250
    In this case the reduction is 40!
  28. Replies
    18
    Views
    7,196

    Re: AC servo Panasonic and Mach3

    Russ
    Why? I switched to the metric system.

    265890



    I want to at 3000 rpm of motor have feed about 5000mm/min.
  29. Replies
    18
    Views
    7,196

    Re: AC servo Panasonic and Mach3

    I have a ESS, but do not use it yet. However I tried it work, but had the same mismatch as without it.
    With the current setting, I can not increase the feed more than 300mm/min. I get an error and...
  30. Replies
    18
    Views
    7,196

    Re: AC servo Panasonic and Mach3

    Russ,

    The ball screw with 5mm per 1 turn.
    I have ethernet smoothstepper.
    If I will set the value of feed more than 300mm/min, the servomotor speed increases above the maximum 3000prm and...
Results 1 to 30 of 107
Page 1 of 4 1 2 3 4