Search:

I'd like to high speed machining too,pls. help me

My machine has 998 system error (parity rom) so I cannot read the parameter from the machine by RS232.I can send you the parameter list attached with my machine, if you still need it.I have checked...

Hi gabedrummin,
I have a OMA Elox wirecut machine.It's a good machine but.. now on the screen has display "SYSTEM ERROR 998 "and ... nothing happen .I know I have to burn new EEproms to fix it but...

All you need are an eprom programer....take off the Eprom from the board and put it into the programer to read the content of the Eprom,save it to file.
You can use these files for back up purpose...

Connection unit or PC card (if exist)may be in trouble

What 's Fanuc controller? I think you have to re- input the option parameter
tungtung

After you initialize bubble memory ,you must depress key 4(bubble )to enter the screen:
Bubble initialize
*function key
1:write by tape
2:write by manual
3:display loop data
origine :return to...

The 6M can used the red cap motor.I am sure your machine is 6M with AC servo motor(red cap motor).Your machine model O is of series O/P/Q/R wirecut EDM.You can check it when boot up,on the screen...

When you initialize the buble memory you must switch "BMU switch " to ON position (NOT the parameter SW to enable) it's on upper side of the master print.

Are you sure it has Fanuc OM or 6M?

Your "setting of parameters" is enough to get your machine running,the parameter 0 to 160 for machine running ,1000's,2000's,3000's are for pitch error compensation of X,Y,Z axis ball screws.About...

You have to perform some steps to bring tool No 01 to reference position before operating in auto mode,PM me
tungtung

I am sure your Elox wirecut is Fanuc 6M,the M42@M47 are no meaning in this case.You can read the operator manual for Fanuc 6M to perform the input,output,delete... the program , PM me for more help ...

So far as I know there are no equivalant of DIO controller MB14235,it's a custom IC
tungtung

You can see on the screen about few second when boot up .I guess that is FANUC SYSTEM 6M and SOFTWARE VERSION ....

Hi
If your option parameter 905 is 0001000 ,your controller do not have any of
PMCL/M,so you cannot display the ladder
tungtung

Can you read the parameter 905 of your machine?

Quote]
My first thought was that that the Z reference home didn't home out right so I re-homed the machine. The machine appears to be homing correctly and it still goes to the correct second Z...

I wonder if the 9000's option parameters are the same?
Can anybody send me a typical 9000's parameter of 12M?
Thanks

The machine is OKK MCH600,I don't have the maintenance manual for this machine.Can i copy the general and specific parameters of the machine with same model OKK MCH600 but with Fanuc 11M?Does anybody...

Does anybody have the Fanuc 12M's parameter list?
Thanks

Thanks for your help,Stevo
I tried as you said ,parameter 2205: 00000100 but ...the Japanese is still display on monitor.I need the manuals for 12M,I don'd have the operator's manual nor maitenance...

Hi evrybody!
I am new to Fanuc 12M ,can anyone help me how to change the Japanese display on Fanuc 12M to ...English? I think there are a parameter... but I don't know or ...I have to change the...

Hi guhl
It' s FANUC system 0MC
Thanks

Hi Al
Can you tell me where/how i can get the FANUC PMC Model K/L/M programming manual(ladder language) B-55193E.I have trouble with ladder of OMC/ATC
thank in advance

Hi
What is the meaning and its use of 26F and how to reset keeprelay bit?
Thank

Many thank philsereng
My Fanuc OMate MC do not have the PMC card ,only 2 ROMs OE1 &OE2
I have tried clear the memory by push Reset+Delete while power up and reloading the parameter
but the CNC is...

I have a ISEIKI Fanuc OMate MC , I move it to other location when I boot the CNC display :

PMC load select
1. Load from I/O
3. Run
4. Run without...

Hi
Your X Y Z servo ready singal go out
duccnc

Hi
It cost 200$
duccnc