Search:

When I try to make a program, I draw the part, and then try to generate a toolpath. Afterward, the toolpath show huge red marks where the tool plunges to zero after doing the roughing and then again...

Has no one ever come up with a suitable replacement for these manifolds if they are expensive and a problem? Where is the best place to buy if I do need them? Can the manifolds not be cleaned or...

First off, thanks to all in the past for the help I have received. INVALUABLE! Now after I recently replaced the 3.2a F13 fuse in the rear cabinet on the power module(still dont know why it went) I...

Thanks for the rapid reply, underthetire,
It could be a circuit breaker, but the fuse is a 3.2 amp fuse located at position F13 on the power supply. The last time I posted the fuses on the power...

OK, thanks to all who have to tried thus far(my sanity is only intact due to the support by you guys, and David La at Ellison) I found a contactor(I believe) marked CMM on the board that had...

Thanks for the suggestions, moving probably won't happen. Any thoughts on why this may have happened? I heard that Mori's can be sensitive but am not clear as to how the incoming electrical would...

How would I find the short? I live a long ways from anyone civilized and am not Terribly helpful in a town of 1000 people.

My machine was working great yesterday and then when I went to startup today the CRT won't turn on. Some of the LEDs in the back panel are not on either. I checked several fuses but no luck. Any...

Found limit switch not properly depressed. Thanks for he programming suggestions on my startup.

Could anyone advise as to why the start to this program has been rejected?
O0004;
(CANAM-SIDE2);
(SET-TOOLS-TO-JAW-FACE);
(T1-WNMG);
N10 G54 S1000;
N20 G28 U0 W0;
N30 G50 S1000;
N40 G90;
N50...

First off, thanks to all who helped me in the past!
My problem this time is that the power comes on but the screen has the EMG light come on solid and then on the bottom of the screen has
MDI ...

The door was open and the limit wouldn't let it run. Now I have to figure out offsets, etc. The workpiece stick 7" out of the chuck, and using the chuck jaw faces for reference, I have values of...

If it were a noncompleted zero return (which I thought I did) or turret position, what would I look for, or how would I correct this

Thanks for the help, I found and replaced a 3.2a fuse on the main board and am powered up again. The problem that led me to hook up the rs-232 was still there and that is when I go to run the...

So is the best method to just start pulling these items and testing resistance across the pins to see if there is one that is bad? Where do you reccomend I get replacements if I find the culpret?

Which fuses are you referring to? I am a machinist not an electrician, and am trying hard to learn as I go.

Thanks!

I forgot to mention that just before the screen went blank, the oil fill was low and had two alarms shown on the screen. I doubt that they would cause the problem, but thought I would bring it up...

I just hooked up me lathe to a cord to transfer a program over(the first time I have ever tried to do this, if you look at my prior posts, I have been working at getting the lathe up and running) and...

Got it running! Can't hardly wait to start puching out widgets!

I am unsure as to how to open up the travels. I have the maintenance manual for this machine but not the programming one. I am concerned if I arbitrarily punch numbers in without an understanding,...

As the title says, I got it to move, but now that I am on the soft travel (1) I need to know how to unstick it!

Thanks to all who have helped me in the past, I am trying to take baby steps and...

I have an SL-25 with a Fanuc 10T control and lost the parameters. I am told I need parameter from someone with a Mori with a close serial # and your is only one digit off. Could you reply to this...

Did you have success, and if so, how
We lost our parameters (SL-25 with Fanuc 10T) and am not having success in re establishing them.

Thanks

I cannot thank you enough for your help! I believe this is what the internet was made for!

These are all possibilities, just use a multimeter to gauge as to if all the limit switches are working, or are there other method of checking, as I mentioned there are no alarms coming up, and the...

The change of parameters doesn't seem to change things. The dial which toggles from edit to mdi to jog rapid and zero return doesn't seem to be picked up by the control. The bottom of the screen...

The tailstock I have has a steel dog on the front of it that you can tip and have the turret drag it to the proper location. Which one would this be? Programmable or not?

This is an 89 Mori with 220 3 phase coming from a step down transformer. After working the weekend on double checking parameters, etc, I have the chuck opening and closing, the tailstock moving in...

Our incoming power is 480 v 3 phase, stepped down to 220 via transformer. The serviceman was referring to the power being "Y" vs star. Any thoughts?

I just had a conversation with a local electrical worker and he suggested that maybe the problem I am having with my mori lathe is that the incoming power is maybe inappropriate for the lathe. We...