501,601 active members
5,232 visitors online
Register for free
Login

Search:

Type: Posts; User: CadCamSam

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    1,451

    You are in the Giibbs forum. Let's assume he is...

    You are in the Giibbs forum. Let's assume he is using Gibbs.

    Unsuccessfully

    Look at the picture he posted.
  2. Replies
    1
    Views
    458

    Definitely drill.

    Definitely drill.
  3. Replies
    2
    Views
    593

    Long runs...Okuma Short runs...Mazak Okuma is...

    Long runs...Okuma
    Short runs...Mazak

    Okuma is a better machine, but a mazak is much faster to program and set up.
    Avoid fanuc or Haas lathes. They are ok for mills, but they are the worst for...
  4. Replies
    17
    Views
    286

    As much as MC would like to claim that their...

    As much as MC would like to claim that their software runs on most PC's, it does not. First of all, MC has ALWAYS had problems on Radeon cards. You really need an nVidia Quadro card. I would...
  5. Replies
    17
    Views
    286

    what are the specs on your PC?

    what are the specs on your PC?
  6. Replies
    2
    Views
    142

    Also, make sure your parenthsis in your comments...

    Also, make sure your parenthsis in your comments are correct.
  7. Replies
    2
    Views
    142

    You may be using a G or M code that the machine...

    You may be using a G or M code that the machine does not understand or have the option turned on.
  8. Replies
    4
    Views
    197

    The ones being shown wrong are usually from MC...

    The ones being shown wrong are usually from MC reps. I have busted them on this
  9. USE TANGENT FORMULA: tan ang = opposite...

    USE TANGENT FORMULA:
    tan ang = opposite side(radius value) / adjacent side
    then multiply by 2
    then calc flat

    82deg csnk =41deg ang
    1" cnsnk dia = .5 opposite side

    tan 41=.8693
    x.5=.4346...
  10. I would try: 2x flute length (16mm) doc 20-25%...

    I would try:
    2x flute length (16mm) doc
    20-25% of tool dia (1.6-2.0mm) radial width of cut
    .254mm MMPT feed(mm per tooth)
  11. Replies
    1
    Views
    139

    T04;(tool wait position) M06; (tool change) g0...

    T04;(tool wait position)
    M06; (tool change)
    g0 g90g54x0y0s500m3t05;(prestage next tool while positioning and turning on spindle)

    What you are doing is calling a tool change before a tool is in...
  12. 2500rpm because you cannot reach recommended...

    2500rpm because you cannot reach recommended 40sfpm
    .0008-.0012ipr
    peck 100% drill dia

    use powdered metal drills and avoid pecking
  13. 2500rpm because you cannot reach recommended...

    2500rpm because you cannot reach recommended 40sfpm
    .0008-.0012ipr
    peck 100% drill dia

    use powdered metal drills and avoid pecking
  14. wHY WOULD YOU WANT TO? jUST DOWNLOAD THE FULL...

    wHY WOULD YOU WANT TO? jUST DOWNLOAD THE FULL CRACKED VERSION AND INSTALL ON pc NOT HOOKED INTO THE INTERNET.
  15. Replies
    1
    Views
    176

    T1M6(probe) G54 G90 G0 X0Y0 G43 Z20. H1 G65...

    T1M6(probe)
    G54 G90 G0 X0Y0
    G43 Z20. H1
    G65 P9832 (probe on)
    G65 P9810 Z5.(5mm above Z0)
    G65 P9811 Z0. S1.(PROBE Z0.)
    G65 P9814 D136. S1. Z-.3 ( boss dia)(use G54)
    G65 P9833 (probe off)
    ...
  16. It's spam.

    It's spam.
  17. n_op = op_count * 10 *n_op I prefer to make...

    n_op = op_count * 10
    *n_op

    I prefer to make the N number the same as the tool number
    n_op = t$
    *n_op
  18. Thread: Kitamura

    by CadCamSam
    Replies
    1
    Views
    113

    There should be a push breaker in the electrical...

    There should be a push breaker in the electrical cabinet.
  19. Replies
    6
    Views
    240

    I see. I would wonder if you have a X axis...

    I see. I would wonder if you have a X axis encoder for rigid tapping. That may be an option, or not properly setup. Try doing the same on the other machines.
  20. Replies
    1
    Views
    121

    Good luck with spectrum Multi-DNC. They have...

    Good luck with spectrum Multi-DNC. They have awful tech support.
    I would STRONGLY recommend contacting Joe Hackman at Managed Solutions. He is brilliant and deals with Cimco.
    We had nothing but...
  21. Replies
    6
    Views
    240

    check out these parameters" 3705 B3(sgt) 3761...

    check out these parameters"
    3705 B3(sgt)
    3761
    3762
    5200 B1(vgr)
    5201 B2(tdr)
    5203 B3(rgs)
    5241
    5242
    5243
  22. Replies
    0
    Views
    81

    Fanuc 16iM M99/M30 problem

    Niigata HN50C Horizontal mill.
    I just recently wrote a program to have the spindle come down to the table to pick up large tools.Here is how it operates:
    Program:
    O10
    Calls blank tool
    Calls...
  23. Thread: Planes

    by CadCamSam
    Replies
    2
    Views
    138

    If you right click on the plane and click "edit"...

    If you right click on the plane and click "edit" you can rotate the plane as you wish. Routalot is correct. No way to know the angles of existing planes without creating and analyzing geometry or...
  24. Replies
    1
    Views
    177

    I use a piece of steel banding. I fold it so it...

    I use a piece of steel banding. I fold it so it works like a spring. We always have used banding laying around for free.
  25. Replies
    1
    Views
    182

    " I do expect the post cost should be minimum" ...

    " I do expect the post cost should be minimum"

    You get what you pay for. Do you work for nothing?
Results 1 to 25 of 73
Page 1 of 3 1 2 3