Search:

I only get those pinout details at Meldas M0 manual. But there is no description for those pins.
We are waiting some Mitsu Expert Here.....!!!!!

I have servo drive TRA60C, and I'd like to retrofit with new control.
But I have a problem to find signal command from servo drive at ZP1
I've got some document from Meldas M0 but there is no...

Case closed when "GURU" said so.. LOL
Thanks Dan!!

My machine didn't show the current program in DNC mode.
What parameter should I change to show current program in DNC mode?
It looks like a blindman operating the machine
Does anyone can help me?

I have a problem with my spindle drive A06B-6055-H103.
After I changed two diode that mounted to transistor module, If I start spindle CW or CCW, the resistor module at connector 6-7 (4 ohm) keep...

Does anyone have electrical wiring diagram for Spindle Drive type : A06B-6055-H103 especially for high voltage section.
After I change diode at TM4 (diode with red stripe and blue dot), the resistor...

yes of course sir.. I've tried with no load, just lay on the floor. the motor use Pulse coder 2000 ppr

yes thats right Al, still on X at + direction.
what do you mean with BS? ballscrew? I've tried with no load, just lay on the floor. the motor use Pulse coder 2000 ppr

Did I mention whole unit? which mean top board include base of drive.
I'm not really sure there's a problem with DC drive (TM,DM). There is something with voltage command. but how come?

yes precisely... did you mean noise that affected to command signal? I have the manual doc with scan quality

the 1st thing that I done was disassembled motor from ballscrew. checked the carbon brush, remove and clean armature from dust with clean dry compressed air.but nothing change even I swap the motor

3 axis are identical. A20B-0009-0320. I already swap whole unit (drive & motor) X to Y but had no luck still vibrating on X. I haven't swap with Z axis

Like I describe, seems look no problem with pulse coder. It works at minus direction smoothly. But I'll double check just for make sure

Is it Freq to Voltage Converter IC? where is the location on master PCB?

where is Al The Man and Dan Fritz ? I need you here ASAP

I swap both servo and drive with Y axis but the problem still on X axis
I checked the DIAG 713 bit 4-5 works fine for Pulse coder

I have several problem with fanuc 6MB at Yamaguchi MC
1. when I move X axis to (-) direction it goes smooth. but if I move to opposite (+) direction, the servo vibrates so hard.
2. its happen to Z...

Hi guys,
I have a problem with my machine TAKISAWA TC-1 with Fanuc OTC Control.
When I make an Index for Turret, its won't stop and keep hunting.
What should I check first? I saw there is an...

let me describe my case one by one
when the 1st time I turn on the machine, about 3-5 min the alarm show up (25 F Servo Amp X)
I checked the drive it show FIN OH Led was lit on X drive. I swapped...

My QT10 show 25 F Servo Amp Alarm even I didn't move all axis.
I checked the servo amp at backpanel, it shows FIN OH Led lit. I swapped the drive X <-> Z but the alarm still on X Servo amp.
If I...

great reply Iron-Man...

this is what I lookin for.... May I discuss with you privately later?

Now I'm using perf board for a while.If I found a great source for schematic maybe I planning to etching a PCB later.

Okay Al, I try to connect this "messy" wire first

sorry for misexplanation..
before I hook up to the machine, I'd like to test it first with all driver connected
of course I need actual isolated to protect my PC's.
Any idea Al? I've read on...

Hi guys,

I'm on the way to build new mini lathe machine for simulation using mach3.
I'd like to make breakout board DIY. But I can't find the schematic/layout design.
Does anyone can help me to...

try meau.com

Does anyone can help me to rewiring for MPG (BP1 to BJ1) connector on Mazatrol T1?
also Jog Handle switch cable was bitten by f*ckin rats!!

Thanks
Andre

Anyone can help me to give a sample to program with canned cycle on heidenhain TNC355

example : 3 row x 5 column, cycle process : After make a 30 mm depth drill than continue to tapping cycle.

I already open the email that you sent to me.
But I doubt about parameter.
Is Pr.50 or Pr.51 because there is a different between those document.
Which one that suit with my servo drive?

Thanks

I would like to get those document. especially main parameter manual.Would you send it to my email?
I really appreciated it.
my email : [email protected]

Thanks

Hi,
I have Panasonic Servo Drive Type MSDA 043A1A.
I want to reverse my motor rotation (CW --> CCW, CCW --> CW)
Anyone can help me out? What should I do?
Which parameter should I change? or Just...

No, I haven't order yet. I will search on local market.

Does anyone know what type of linear guide and ballscrew before I dettach from saddle? Include detail specification would be appreciate...