508,006 active members
3,897 visitors online
Register for free
Login

Search:

Type: Posts; User: Renatox_

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    407

    Re: Error M01 in CNC 432 in MH500C

    Replace the CENT_PROCMOD put parameters again and this started working.
  2. Replies
    0
    Views
    34

    Fanuc 11m, does not start

    Hi good day,

    In a Kitamura center with 11m fanuc control, when i turn on the control the following menu appears and the operation panel does not start.

    FS11MF 2122Q
    Romtest: end
    Ramtest: end...
  3. Replies
    4
    Views
    407

    Re: Error M01 in CNC 432 in MH500C

    I could solve this problem, replace the batery of 6v, i put all the constant, then this almost work.

    in test obtain alarm of Drive mod3, Input Module1, CentPro. , this look like electronics error...
  4. Replies
    4
    Views
    407

    Error M01 in CNC 432 in MH500C

    Hi good day i am checking cnc mill MH500C with control CNC 432, i obtain the errors M01 and I01,

    If 19RSS1 = 0 , error M01 appears (checksum fault MC memory RAM)
    if 19RSS1 = 1 , screen constant...
  5. Replies
    0
    Views
    218

    Bridgeport Z15-1-240v bosch servodriver

    Hi good day, i have saveral servos Z15-1-240v, as photo sample.

    I no have the manual and connection, i would use this for drive other motors. Some you know the connection this have X6, L1, L2, U,...
  6. Replies
    3
    Views
    587

    Re: Maho 500C, error M01

    thanks, the pcb original is fault, i put these and chessboard same appears, i put the centr. proc. mod of the other maho and error M01 appears, as you say, this can be parameter, i no have form of...
  7. Replies
    3
    Views
    587

    Maho 500C, error M01

    Hi good day,

    I am checking a Maho 500c, this have Philips cnc 432, the second pcb of the side left is Centr. Proc. Mod have fail, i remove this and screen have the form of chessboard, then i put...
  8. Thread: Maho mh 600e

    by Renatox_
    Replies
    6
    Views
    831

    Re: Maho mh 600e

    HI viorel23cnc, the arameters o constants for MAHO MH500C, have you this?

    thanks
  9. Replies
    2
    Views
    361

    Re: Linear Encoder Maho600

    OK thanks, refer a 5um/meter, it is ok.

    Renato
  10. Replies
    2
    Views
    361

    Linear Encoder Maho600

    I all, I have a MAHO MH600E cnc 432, but no can move the x axis, this say Alarm X02: (Alarm measuring system fault), i suspect what is the encoder model AE LS 403 Heidenhain.
    Seeing the datasheet...
  11. Replies
    0
    Views
    1,126

    Alarm 351: X Axis Communication

    The voltage source of 15v, internal control, has been damaged, the reason was a short on the source wires that go to the turret. What I did was put in parallel, out of control, a switching source...
  12. Re: driver A06B-6079-H105 terminating cinnector

    Thanks for the data.

    I have three connector air, and four connectors in the A06B, these are:

    JX5
    JX1A
    JX1B
    PWM11_JV1B,

    the connector terminating is connected a JX1B, the other a JV1B and...
  13. driver A06B-6079-H105 terminating cinnector

    Hi good day,

    I was removing the connectors of 20 pins of these drivers A06B-6079-H105 and i lost the terminating connector.

    I guess this take a few bridges, i can see the datasheet and...
Results 1 to 13 of 13