Sounds like instead of a tech you should have called a preist for an exorcist.
Type: Posts; User: Leelund
Sounds like instead of a tech you should have called a preist for an exorcist.
Here is the page out of the manual158213
Hi Mike,
I was adding info to my original post when you posted the picture. I found a 5F alarm in the MDS manual. It mentions the external contactor being welded. I guess anything along those...
Hello Mike,
I don't have a listing of a 5F alarm either. If you look in your electrical cabinet the Z axis amp should be displaying an alarm code as well. What is the drive saying? What model is...
S12-GRDSPC- The grid interval of your axis. Usually you can find this listed in your electrical manual that shows your motor and encoder wiring. It usually says the grid spacing.
S23-VIL- Speed...
We use individual mist collectors, smog hoggs, Torit, on our MC's. Coolant still gets in fans. We change/clean CNC filters every 2 weeks and they are black and slimey. Oilcooler filters- same...
Is it firing the open solenoid and trying to open? If so, it sounds like the linkage has is bound up. Turn off the air to the machine and try to manually pull the door open. With no air on it, it...
PLC parameters are listed in your electric manual. Pretty sure there is a description also.
Old ones were 12 volt bulbs. Base of the stack had a transformer in it. 120 ac in 12vdc out. New style are led light stacks. pretty neat. Probably pretty pricey from Mazak. Google "Patlite" and...
I don't think there is both a limit switch and prox switch. It's probably one or the other. We no longer have the machine and I'm trying to remember 25 years back. I can't remember what type was...
Go to the diagnosis interface page and see if H05 bit 3 turns to a 1 status when you shift to low gear. Make sure that H05 bit 2 goes to a 0 status also. Both should not be "on" at the same time. H05...
U R on it Gridley! Especially if it says gear 0. Control doesn't know it finished the shift. Tweak the sensor a little. If you cannot get there, or have to move the switch a lot, then maybe the...
Unwire the motor from the drive and see if it powers up to the ready condition. 32 alarm with the motor leads unwired will mean drive is blown. Power transistors may be shot in the base of the drive....
Or here- http://www.omnivisionusa.com I have installed their retrofit in as little as 20 minutes. Maybe a bit pricey though. You will have to decide. My outfit has deep pockets.
Did you change the battery with power on? If so, did you try to recycle the power at the main disconnect, then power back up?
AIR! If I recall they had air chucks installed on them. Gotta have air on to the machine and the pressure switch made.
I may be way off base here but I think I recall something about a spindle zero speed output from the SX controller to the T1 controller before it will even try to shift.
The problem could be the encoder cable itself. One of the wires may have parted or broke. Check continuity from the honda end at FX06 through the cannon connector at the encoder.
If the cable...
The TL LED on the MV4 is a tach loss. Led1 is a direction command I think. You need to clear the tach loss by recycling the main power off/on. Check to see if the red tach loss alarm has cleared. If...
Diagnosis Key -> Hit the Window Button on the lower righthand corner of the control -> Click on Accumulated Time. Same from the top where it says File Edit Window Help on the top left corner of the...
Not familiar with the Meldas 60, but you would think there would be a 2nd Home or Number 2 Zero position for Z axis. Should be a Machine Constant Parameter that probably is listed in the Machine...
You're on it nlh! Don't you have to release the reset but keep the OT release in while you jog it off the hard limit? And if I remember right, if it's a VQC type, and Y is over in the ATC area it has...
Our Mazatrol Matrix and 640 Pro's all have the next tool ready and waiting in the atc arm and the spindle tool magazine pocket called up ready foe the return after the exchange. Maybe a Fanuc thing?
Onboard batteries on 442, 471 or 472 or 474 if so equipped. 3.6 Coin cell in O62 battery box under the 721 drive.I think you should have three 3.6 coin cells and the 6 volt sealed lead acid total.
Machine parameter M1 is rapid feedrate.
1. Large tank and pump are for hydraulics used on your machine.
2.Yes, if the regulator valve is in line with the cooler pump then it does pump out to the spindle. If it does NOT pump out to the...
There should be an input(tank) hose and a supply(pressure) hose coming and going to the chiller unit. The pressure line should be noticeably cooler than the return line if the compressor is cooling...
Look up your model number and maybe you can find a operating manual at Diakin. Yellow-(original is white)= Power On; Green= Cooling: Red= Alarm. The green means the cooling compressor is running. Red...
Do you have the MAC or Daikin Chiller unit? Mac has a little condensor on the side of the controller about 6" x 8". I think it cools the hydraulic unit oil though so it is of no concern. Are the...
Check your servo drive(s) and spindle controller for alarms. Check the obvious, tripped breakers, blown fuses, and overloads tripped.