We would be glad to assist if you do not want to do this yourself. Contact us with details @ [email protected]
Thanks
Type: Posts; User: dneisler
We would be glad to assist if you do not want to do this yourself. Contact us with details @ [email protected]
Thanks
Hello and thanks in advance.
I just got this used lathe and finally got it hooked up to electrical service and when I turn the machine on all is fine, then I can usually move the table for 10-20...
Thanks, I am going to give it a look when I get a chance. I have a couple more parts to finish before I can tear machine down. Machine is a 2006 model.
Can the humphrey valves be cleaned or must...
First off, thanks ahead of time for any help or assistance you may have.
This weekend my super mini mill started acting funny on tool changes. I have 2 items I have noticed.
1. When I remove a...
Anyone?
Sent from my iPhone using Tapatalk
Well it appears to be working fine. Thanks for all the help. I am now trying to verify everything is working.
So how would I verify the oiler is piling the screws ways and spindle I do not...
Ok going to give it a try.
Sent from my iPhone using Tapatalk
Voltages to ground
1 - 123v
2 - 123v
3 - 225v
Is this all acceptable? So #3 needs to connect to center lug on the SMM. Sorry I am just trying to be very carefully setting this up. I spent...
I just a 2006 Haas Super Mini Mill deliver S and I have some questions about hooking it up to my rotary phase converter.
I would normally assume T1 connects to T1, T2 to T2, and T3 to T3. I have...
I am doing fall cleanup around my shop and I have some items I need to get rid of. If you have any interested in any item please PM for details.
3 - PCNC 1100 S3 Drives - Used
1 - PCNC 1100 BOB...
I tied a spiral flute and it stalled spindle but is more of a bottom tap. Do they make a spiral flute that is a bottoming...
I've considered that as well but I am using square stock it really doesn't work.
Sent from my iPhone using Tapatalk
Works fine in a collet holder. I was seeing thread quality issues and switched too a floating holder from maritool. Didn't make any difference really. I then bought a axial indicated where I could...
Yes I do, but for what I run. It requires me to change collet, set the one part, change collet back to my square stock collet and it takes to long. If I ran round stock, it is easier.
I have to do...
Thanks, I may have exaggerated a bit, but it is enough I can do anything until I re-zero.
Anyone consider upgrading this POS's?
I can re-home and have seen as much as .100 difference. This makes life hard sometimes!
Gotta love iPhones autocorrect. Oil line
Sent from my iPhone using Tapatalk
I know the issue now for sure. It is a living line clogged up. I manually lubed the way and it runs fine for a while and they problem will come back. Lube it again and I am good for a while again. ...
Nope I checked that.
I think I got it fixed now, will confirm tomorrow.
Ok maybe it is not just drilling...
I was doing a part I done last week 125 times with no issues in 1018.
Today I did the same gcode and it was missing steps doing a OD turn. I was doing .02...
I can run these on my mill(PCNC1100), much faster than you quote and get a great drill finish. So why is the lathe so much slower and will not run it?
Yes my holder sticks out to far, that is...
1000rpm. .005 fpr is 10 times worse. I can visually see it missing steps. It kind of jumps back and forth. It touched stock and it did not move. New TG or YG(I can never remember) drill bit. When...
I'm new to the lathe world so I was using the same speed feed etc that I was on mill for same part and hope and I would get 1000 plus parts out of the drill. I'm just not getting this lathe stuff...
I am just drilling 27/64 (.4219) which is smaller than your pilot size. I need to get this process going fast as I have 1200 parts that need to go out quick, to the point I need to machine at least...
I will put in a new drill and give it a try with say 1000rpm and .005fpr?
I am pecking at alternating 1/8 and 1/4.
Sent from my iPhone using Tapatalk
Not sure what you mean by adapter.... Also running less rpm and faster would require more z axis power right? If it is already missing steps then? I just don't understand why I am missing steps. ...
This after one part how much I lost in Z. http://uploads.tapatalk-cdn.com/20160805/62f8442d69b3425dd5e5ffa51847e529.jpg
Sent from my iPhone using Tapatalk
This what I am running now. I have got to figure out why I am losing steps. . http://uploads.tapatalk-cdn.com/20160805/55de9d424152be601b236b4628b71d6b.png
Sent from my iPhone using Tapatalk
Drill bit is a good PTD bit. That feed don't help me any really. I have thousands to make and need to go faster than that. I pretty much have determined I am missing steps somewhere.
Sent...