584,817 active members*
4,983 visitors online*
Register for free
Login

Search:

Type: Posts; User: Pucas

Search: Search took 0.01 seconds.

  1. Re: Turret Issue after Battery Dead Al-62 SKT21 LMS built 2010

    Should be: system -> PMM (power mate mng) -> Parameter
  2. Replies
    1
    Views
    1,796

    Re: KIA SKT 21 Won't Move with Chuck open

    Hi, controller type, alarm no. and machine production year would help a lot.
    Anyways if you still have the issue, give me the information and I will help you.
  3. Replies
    2
    Views
    1,669

    Re: Hyundai SKT21 LMS Sub Spindle Chuck Open/Close

    Hi! Normaly there should be an operating panel of sub spindle. Can you share a picture of your operation panel?

    487911
  4. Thread: Keypad issues

    by Pucas
    Replies
    1
    Views
    1,429

    Re: Keypad issues

    Hi there! You can try to change nc parameters as below:
    - 3100 bit 2: 0->1
    - 14705 bit 0 and 6: 0->1
  5. Replies
    1
    Views
    1,107

    Re: Hyundai Kia SKT180 Wait Code Problem

    Hi,

    try to set D10.1 to 0
  6. Re: KIA KT 20 with Fanuc O-M Control need Electrical prints and Manuals

    Hi,

    You can check parameter:
    - 0577 Spindle speed command offset (always set to 0)
    - 0516 Spindle speed command gain adjustment (always set to 1000)
    Which spindle motor do you have?
  7. Re: SKT210SY - Turret not aligning, AL-66, alarm 2066

    Hi!!!

    My questions would be:

    - are the y, x and b axis in reference position (zero return position) when you command the tool change? check signals F94.0 (x), F94.2 (y 1st zero return)/ F96.2...
  8. Thread: pachomandella

    by Pucas
    Replies
    1
    Views
    637

    Re: pachomandella

    Hi!!! I think you already solve it. but in case if not you can check some points as follows....
    - Check the parameter 1321. You should have a blue folder in electric cabinet. Find the 1321 in data...
  9. Replies
    3
    Views
    3,122

    Hi, I don't know the machine but it sounds like...

    Hi, I don't know the machine but it sounds like solenoid valve problem.
  10. Replies
    6
    Views
    2,736

    Hi, Give me your email address. Thanks

    Hi,

    Give me your email address.

    Thanks
  11. Replies
    3
    Views
    1,404

    Please write me your email address I will send it...

    Please write me your email address I will send it to you.
  12. Replies
    3
    Views
    1,404

    I don't think that you will find the Manuals...

    I don't think that you will find the Manuals online... but maybe I can help you. I will check what can I find for you tomorrow.
  13. Sorry my mistake. Should be M124 \ M125.

    Sorry my mistake. Should be M124 \ M125.
  14. Hi, it's M123 (Sub sp. center rigid tap mode...

    Hi,

    it's M123 (Sub sp. center rigid tap mode on) and M124 (Sub sp. center rigid tap mode off)

    E.G.

    G80
    G28U0
    T0900
    G00X0
  15. Replies
    6
    Views
    14,728

    amp alarms: 211552

    amp alarms:

    211552
  16. Replies
    6
    Views
    14,728

    2060 TURRET AMP ALARM Cause: - In case that...

    2060 TURRET AMP ALARM

    Cause:
    - In case that alarm is issued on the turret AMP.

    Actions: /Procedures:
    - Take measures by means of reviewing the maintenance manual of FANUC I/O Link ...
  17. Does it have PMM? If yes, set the turret to pos....

    Does it have PMM? If yes, set the turret to pos. 1, PMM parameter 11#0 to 0 to 1, power off/on.
Results 1 to 17 of 17