I could use some help too.
[email protected]
Type: Posts; User: Billet Carb
I could use some help too.
[email protected]
I will try that in the morning.
No, I do not know how to do them.
Two weeks ago today, I came into work to find the electricity had gone off during the night.
The heater I use special for the machine had gone off, and not reset itself, that was the clue.
It was...
Hello,
I have a Chevalier VMC 2040 with a faulty drawbar. I am not able to remove it to replace.
If you have any experience with drawbar replacement, please contact me...
Regards,
John
I just started using Predator Editor.
I hope this is a simple question. When using Backplot,,, I want to make the G code on the left side of the screen larger so I can see the information easier,...
While learning how convert photos into engraving g-code.
It takes an amazing amount of memory ! The program made an odd move during simulation, then stopped.
After that,, even very small programs...
I wish I had a new story to tell. I was a victim of the same old story ! Give a low quote to get me in the door, then raise the price. If that was not bad enough, it lasted only till the third time I...
I wanted anybody who reads this thread to know it is correct. I had a bypass wire on my door come loose and gave me this alarm. Chased it down,, fixed it,, all is good !!
My machine was running today. I went to load a new program in and fond the machine none responsive.
Restarted the machine to find it in Overtravel in all directions at one time. It did this when I...
I have an intermittent error code 424 servo alarm y axis detect error
any suggestions?
Regards,
John
First, I want to thanks all who have given me help along the way !
My question for today is;
I have a Chevalier 2040 with a Dex cans tool changer and I want to completely tune it up and put in new...
Thanks so much!
Simple when you know what to do ...
Regards,
John
Hi ,
I have a new to me Chevaliar 2040 with a Fanuc OMD controller.
I want to retrieve files I have loaded into the library.
How do I do that?
Regards,
John
[email protected]
Chevalier 2040 Support with Fanuc OMD controller
845 473 1136
Machine starts up then gives 401 Servo Alarm : VRDY OFF
can anyone help with this?
Regards,
John
I am look for support for a Hitachi Seiki HC 400. If experienced with this machine , I can pay for support.
The machine has a Fanuc 15 M controller .
Recently it has developed an intermittent...
I am look for support for a Hitachi Seiki HC 400. If experienced with this machine , I can pay for support.
The machine has a Fanuc 15 M controller .
Recently it has developed an intermittent...
I was sure hoping someone knew how to take the Bobcad .NC file and get it into the Fanuc 15M controller?
Still trying to get this done.
I have the correct Bobcad code now, just need to input to...
I was sure hoping someone knew how to take the Bobcad .NC file and get it into the Fanuc 15M controller?
Still trying to get this done.
First I want to thanks all persons who have just some great suggestions!!!!!!!!!
I have made a full set of Bobcad Drawings now, and need to download the post processor to my Fanuc 15M controller....
First I want to thanks all persons who have just some great suggestions!!!!!!!!!
I have made a full set of Bobcad Drawings now, and need to download the post processor to my Fanuc 15M controller. I...
Thanks Rob,,, it works !! I need to check for double's next .
Here is the zip
I am profiling the out side of a simple part. At the top of the part is a stright line. I have worked three days to get it cut along that line as it does all other lines,, no luck.
It rapids over...
Hi Luke,
I hope the file comes through. If not,,, my e-mail is [email protected]
I am profiling the out side of a simple part. At the top of the part is a stright line. I have worked three days to get it cut along that line as it does all other lines,, no luck.
It rapids over...
I have Hitachi Seiki 400 HC with a Funuc 15 m controller ...
I need the G Codes for the full range of 6000RPM's.
There maybe a high and low range.
Willing to pay for over phone mentoring.
Thank you for your responses. I have got the spindle turning now, but are limited to 1200RPM using G code. We are just learning the machine, and are just interested in testing the spindle speed...
Thank you for your responses. I have got the spindle turning now, but are limited to 1200RPM using G code. We are just learning the machine, and are just interested in testing the spindle speed...
The incoming voltage is 120,, 120,, 208 when to ground... when crossed 243
the XYZ & B all worked, just screen came up with an over voltage for the spindle (23 volts).. In the main distribution...