506,200 active members
1,448 visitors online
Register for free
Login

Search:

Type: Posts; User: bmoore

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Re: Partner 1D. Lower Z axis. Machine not under power.

    Put a jack under it and remove the z motor, then replace the z motor once tou have it lowered.

    Sent from my SM-N960U using Tapatalk
  2. Re: Need BobCad V30 post for Milltronics Centurion 7

    Also i have a post processor for bobcad v30

    Sent from my SM-N960U using Tapatalk
  3. Re: Need BobCad V30 post for Milltronics Centurion 7

    Are you using cutter comp? You have to have a lead in.

    Sent from my SM-N960U using Tapatalk
  4. Replies
    3
    Views
    124

    Re: 2003 vm25 7 control

    You have to program a lead in. Perpendicular or at an angle or maybe even arc. You cant come in straight. It compensates in the first move.

    Sent from my SM-N960U using Tapatalk
  5. Replies
    4
    Views
    180

    Re: X axis way covers

    There are springs that connect both x axis way covers under the table. I had to pull the cover, unhook the springs and hook them to a welding rod to keep them from shooting under the table.

    Sent...
  6. Replies
    8
    Views
    276

    Re: Milltronics Partner 1 Series H CAM

    You can go to utilities and info to find out what version of c6 is on it. Sounds like it has been upgraded.

    I had to replace the ballscrew bearings on my vm 17 when I got it. 7204 angular contact...
  7. Replies
    37
    Views
    726

    Re: Partner 1 Series H CSM 09000 files

    get a usb floppy drive, thats what i did.
  8. Replies
    0
    Views
    227

    Re: 2005 RW15 Thrust Bearings

    if you are talking about the angular contact bearings, then they are probably 7204 bearings and can be had from ebay for cheap
    ...
  9. Replies
    37
    Views
    726

    Re: Partner 1 Series H - Problem with Video

    41 is the mcode that calls O9020. If may be in your program folders.

    when you hit the reset button before you home the machine does the red led labled reset on the spindle drive turn on?
  10. Replies
    37
    Views
    726

    Re: Partner 1 Series H - Problem with Video

    Is your spindle drive resetting with the machine?

    What does O9020 program say?

    Sent from my SM-N960U using Tapatalk
  11. Replies
    37
    Views
    726

    Re: Partner 1 Series H - Problem with Video

    Have you tried calling m41?

    M41 (should hear a contactor pull in)
    S500
    M3

    Sent from my SM-N960U using Tapatalk
  12. Replies
    37
    Views
    726

    Re: Partner 1 Series H - Problem with Video

    What does your spindle override on the screen say? I have a lathe that defaults to 0% on start up regardless of the switch setting. I have to adjust it 1 click to get the screen to match the switch....
  13. Replies
    37
    Views
    726

    Re: Partner 1 Series H - Problem with Video

    Csm is a good servo drive, very crisp and responsive. Did you call out a spindle speed? S1000 in mdi?

    Sent from my SM-N960U using Tapatalk
  14. Replies
    37
    Views
    726

    Re: Partner 1 Series H - Problem with Video

    PM me your email. I will send you what I have.

    Sent from my SM-N960U using Tapatalk
  15. Replies
    9
    Views
    256

    Re: Milltronics 3d program

    Go into parameters enter the password, I think it is under control make sure "use full dos names" is set to yes. No dnc necessary.

    Sent from my SM-N960U using Tapatalk
  16. Replies
    9
    Views
    256

    Re: Milltronics 3d program

    Do you have full dos names turned on in parameters. You should be able to load a .tap from your cad cam.

    Sent from my SM-N960U using Tapatalk
  17. Replies
    9
    Views
    256

    Re: Milltronics 3d program

    Are you using fastcam or cadcam?

    Sent from my SM-N960U using Tapatalk
  18. Replies
    9
    Views
    256

    Re: Milltronics 3d program

    Why do you even need the p program? Where are you transferring from?

    Sent from my SM-N960U using Tapatalk
  19. Re: Air Compressor requirements for Spindle/Tool Holder?

    You only need air to open the gripper. Though the machine may not reset if there is no air, but you can change that in the parameters.

    Sent from my SM-N960U using Tapatalk
  20. Re: Machine seems to actually work now... What now?

    Mine is
    Z=1
    X=2
    Y=2
    A=2

    Sent from my SM-N960U using Tapatalk
  21. Re: Partner 1D. Removing X & Y Belts and pulleys.

    To get the big pulley off take out the 2 set screws, and put one in the middle hole and tighten to pull the hub out of the center of the pulley. It's a taper lock.

    Sent from my SM-N960U using...
  22. Re: Machine seems to actually work now... What now?

    I think it's in parms-control homing sequence

    Should be
    Z=1
    X=2
    Y=2

    Sent from my SM-N960U using Tapatalk
  23. Re: Milltronics VM16 Centurion 6 Multifunction Card reader

    Call sportybob he sells the card readers, and can help you set it up. The control will not recognize a card bigger than 2gb unless it is partitioned into 2gb sections

    Electro-Mech Tech Services...
  24. Re: Machine seems to actually work now... What now?

    What's your email. I have a pdf work book for learning the mill conversational.

    Sent from my SM-N960U using Tapatalk
  25. Replies
    11
    Views
    293

    Re: Replacing X Cable Questions

    On my knee mill they go into the round connector then to the contractor, then to the servo drive.https://uploads.tapatalk-cdn.com/20190119/587266ccea3f340b0c24a524b03561f8.jpg

    Sent from my...
Results 1 to 25 of 61
Page 1 of 3 1 2 3