Search:

https://louisville.craigslist.org/tls/6541506144.html

After noticing the bottom of my table in X axis, the slide nearest the front of the machine was not getting oil I decided to pull the table to see what the problem is. The top of my X axis slide is...

Just wondering if anyone is looking to sell a Mikini?
Thanks
Blake

First time using a Bridgeport Easypath, trying to load up programs through the jump drive input.
Not recognizing, Unable to save programs to it or load them.
Any advice would be helpful.
Thanks...

Is Path Pilot Locked? Can you modify Rapids? If this was mentioned in the post and I missed it I apologize. I've seen videos of Tormachs lathe and it's rapids are very slow.
Bake

Actually job was completed, and went very smooth. Just had not cleaned out shavings yet, my employee through a piece of tool steel in one of the vices I had set up to mill down a tool steel block and...

289940289936Just wanted to post my recent experience with Novakon Service, I contacted John this past Tuesday about a really bad mishap I had in my shop regarding my NM-200.
After finishing up a...

Thought I'd share a couple pics of my enclosure on my NM200, little rough around the edges but very functional. The machine runs an average of 10 hours a day, atleast 6 days a week.
Was making quite...

Hello,
I recently purchased a Teco JNEV-101-H1 VFD for a small lathe using a 3/4 horse 3phase motor. I can operate the motor fine using the controls on the VFD itself, but I'm having a hard time...

Yes I understand that it does go to the Servo Drive, I didn't word my question correctly. The encoder has 8 wires? Most I've seen only have 4. I was thinking of going with a Gecko320X by the way....

I recently purchased a small techno CNC lathe, minus the electronics but still had the servos and encoders.
My question is I'm adding the electronics, bob, vfd, power supplies etc. I'm unsure of...

I recently purchased a small little techno CNC lathe, minus the electronics but still had the servos and encoders.
My question is I'm adding the electronics, bob, vfd, power supplies etc. I'm...

Hello,
Thinking of purchasing the Tormach Lathe, I was wondering are you having to create a post processor for the new Tormach Contoller?
I use BobCad V27 currently for Mach3 and Haas Machines. ...

I don't post here often, but thought I'd share some pics of the enclosure I came up with. Still needs to be painted . I kept the original Tormach back guard in place and basically wrapped 1/16 thick...

Very interested in quoting this job, please email me.
Thanks,
Blake Augustine
[email protected]

I installed the spindle VFD with brake resistor upgrade kit a few months back and have been running fine ever since. Now, For some reason When I turn the spindle on it comes on like it should, but...

I was wondering if anyone has used the Leadshine MX3660 with a index pulse card to enable threading on a Lathe. If so, how it would be hooked up?
I've looked through the documentation online but so...

I've seen some pretty impressive cnc lathe machine builds on this Forum. I'm in search of a Grizzly 10x22 lathe that has been converted to CNC, or comparable.
I have thought about attempting a...

Ray,
I ended up not having the board enable terminals connected. I spoke with John late last night and was able to get the board working.
Although I am still having issues on getting the VFD to...

I recently purchased a VFD upgrade kit from Novakon for my NM200. John worked with me over the phone on Sunday and we determined my BOB was bad and I needing a new one. The new BOB arrived today from...

I am installing a VFD and Spindle upgrade kit on my NM200 and was wondering if anyone had any advice or tips that could make the installation go more smoothly. I have the installation instructions...

Hello Michael,
I would like to submit a quote on the 8 pieces your needing.
Please email me at [email protected]
Look forward to hearing from you....
Thanks,
Blake Augustine
Augustine...

Hello EddieO,
I would like to quote the RC Motor Parts your needing made. Please send me an email of the igs file as will as the pdf.
Look forward to hearing from you.
Thanks,...

Hello,
Interested in quoting your job, could you email me the print in dwg or pdf form? Also, your zip code as well, so I can calculate shipping charges. Look forward to hearing from you..Thanks,...

I use the Tormach Shuttle on my Tormach and Novakon. Works very well in my opinion.
Blake

Hello Don,
I would like to quote on the work your needing. I am very capable of performing very close tolerance work that is correct in dimension, appearance, and surface finish.
Please email...

Hello, I would like to quote the plates your needing made. Could you send me a pdf or dwg?
I offer quality machine work at affordable rates with quick turnaround.
Hope to hear from you.
Blake...

Hello Jeremy,
I would be happy to quote the part your looking to have produced. Please email the drawing for quote.
Thanks,
Blake Augustine
[email protected]
Augustine Machine & Design...

197508
It looks as though my Spindle not working on my NM200 Series 2 is more than a loose wire. I ran the machine this morning for a few hours and it worked fine.
I turned of the machine for about...

I operate a part time Machining business which I use a Tormach and a Novakon. At my regular job I run Haas, Leadwell, Fryer, and Milltronics machines. When I went to purchase my machines for my...