Oh, OK. So you were born an expert.
No idea why you think it was nonsensical, it was a perfectly reasonable question. I had no idea what the difference between the two series was.
I'm done.
Type: Posts; User: dvdlock
Oh, OK. So you were born an expert.
No idea why you think it was nonsensical, it was a perfectly reasonable question. I had no idea what the difference between the two series was.
I'm done.
Would you care to elaborate?
Just found the answer. For those interested the answer lies not in the machine but in the Lens system. Confusion
This is from Russ on his SarbarMultimedia YouTube channel:
Hi
Just getting back into Laser engraving and cutting after a few years away. Something that I can't seem to find an answer on is what's the difference between a c-series and an E-series or any othe...
The only thing I have left to suggest is to disconnect/unplug your machine from mains power. Open up the cabinet and check all connections are tightened up.
Also, have a look for a power supply...
Unfortunately I can't help you with measuring power at the laser tube.
When the laser is going through the motions but with no output, can you see the light flashing down the laser tube?
Difficult to say. It looks like it has a single hose to it coming from the pressure line. If thats is the case it may be a diaphragm type pressure switch.
Easiest way to tell is to disconnect the...
Your problem is most likely to be a safety interlock (door switch) or flow switch.
Check you water hose just after where the water goes in. There should be a flow switch there. The laser will not...
John,
I did a couple of tutorials some time back for a guy who purchased my previous Rabbit laser from me.
The tutorials are not the best but hopefully it will help shed some light on what may...
Hi Guys,
Not been on for a while and only just seen this post.
For those that are having a problem with a file not reflecting a change in the output, like changing a name and the laser still...
That's very interesting, many thanks. I have just downloaded a copy of the manual from Leetro.
I'll spend some time to understand your thoughts and see if I come up with a solution.
Thanks again...
If it's a Chinese machine running Lasercut have a look at the layer output (top right of the screen). There is an output checkbox for if you want one of the layers not to output.
Depending on your...
Hello,
Firstly, you haven't said what the material is. It looks like polished aluminium (aluminum) or chrome. If this is the case and you laser directly on to it you will not achieve very much,...
Hi Chris,
Good to hear from you.
It's really just me being lazy. As you know I have all the auxhillary equipment on switches on the control panel. It really is just a case of flicking a switch...
Hi Skip,
The sensei eh!! I think i'll have to put that in my resume and give myself a payrise :D
Good point about the blow checkbox in Lasercut. To be honest it never crossed my mind and that...
Hi guys,
I have a Rabbit 9060 SE 60W running MPC 6515.
I would like to fit a relay to stop/start my air assist pump with the laser output.
Could anyone advise on where I could take the feed...
Not sure about your downloading problems without a bit more information to go on. How are you going about downloading to the machine, any messages etc.
The Corel plug in is selected from the...
Personally I much prefer a good soldered joint. There's only two connections and it's a breeze to do, if you know how to solder.
If you don't know how to solder then the connectors mentioned (we...
Hi,
I used the small air pump that was supplied with the machine. I think it's like the ones used for air brushes.
I have it mounted inside the machine cabinet. The only sound I can hear is the...
Ah! I see where you are coming from now.
If I were to use the control panel cursor arrows and hold one down, mine would also hit the side. It was the same on my previous machine.
Even using the...
Terry,
Looks like you are getting somewhere at least. When you say the head is travelling too far and hitting the frame, are you sending a file to the laser for it to follow?
The reason I ask...
Hi Terry,
I'm not at my laser at the moment but from memory, once you have changed the parameter click the download button. The one you click when sending a job to the laser.
On the resulting box...
Hi Terry,
I am not familiar with Lasercut 4.0, I am using Lasercut 5.1 but I would have thought they would still be a lot of similarities.
I'm not sure I understand quite what you are trying to...
Mike,
Never noticed the rotary in that picture before. I have the roller type and I can see pro's and cons with each. I think once you get going with it you'll probably come up with all sorts of...
Good to hear you are having fun Mike.
I know the lasercut software is quite basic but I find it perfectly good for my needs. Lasercut 5.3 has been issued with some of the new machines but I found...
Hi Mike,
Just wondering how you are getting on with your new machine.
Hope you are having fun.
Dave.
Hi Mike,
Some good points. I never thought about your machine using a different control board.
Yes, mine is connected via a USB cable to a dedicated Laptop. I don't usually use the control panel...
Hi Mike,
You are right, these forums really help. There's a bunch of people from whom I benefited from their experience and now I am able to pay back a little by sharing what little I know. It's...
Hi Mike.
I will probably end up rambling a bit here and no doubt you will already know much of what I will say, but here goes anyway.
Not a bad first attempt. I would recommend you get hold of...
Hi Mike,
You need to convert to a 1-bit image. It's often referred to as a 2-bit. It's just plain old black and white.
Unfortunately our Chinese built systems can't handle greyscale. However, you...