584,837 active members*
5,204 visitors online*
Register for free
Login

Search:

Type: Posts; User: zpsbob

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,194

    Re: Way lube pressure switch

    Shoot me a direct email [email protected]. For some reading I can’t get the PMs to work
  2. Thread: 2000 Kira VTC30

    by zpsbob
    Replies
    1
    Views
    1,339

    Start here:...

    Start here:
    http://www.kiraamerica.com/companyinfoamerica.php
  3. Replies
    5
    Views
    1,943

    Re: Journeyman Mill question

    I'm not 100% sure, but I think that is a drain tube for oil in the headstock
  4. Replies
    9
    Views
    1,472

    Re: Tree journeyman Fault

    Sweet! glad you got it going. Be careful with those Vogel lube pumps. They are very expensive!

    [email protected]
  5. Replies
    9
    Views
    1,472

    Re: Tree journeyman Fault

    There should be a filter in line after the lube pump and a filter screen on the oil intake inside the oil tank itself.

    There are two versions of the Vogel lube system used on these machines. One...
  6. Replies
    9
    Views
    1,472

    Re: Tree journeyman Fault

    From the ladder: MTB FAULT MESSAGE 20: 20 LUBRICATION TIMEOUT

    The machine is not satisfying (closing) the lubrication pressure switches within the allotted time, or if they are closing they are...
  7. Re: Tree VMC 750 (Green Button does not work) please help

    Oh… also… clean the chips out of the two grey troughs with covers on the back of the machine.
  8. Re: Tree VMC 750 (Green Button does not work) please help

    There should be a key switch for “deblock limit switch” I think on the side of the electrical cabinet. Turn the switch, press data reset, then press start. You should be able to jog off switch. Some...
  9. Replies
    1
    Views
    1,512

    Re: OLD Tree mill purchase

    Tree sold the head as a separate assembly and they got glued to just about any type of machine you can imagine. They marketed it as the MH-4 head and it probably got stuck to the Italian iron...
  10. Re: Tree J325, Spindle Won't Start, Overloaded Error, Encoder Error on SD

    Ideally, if you can get your hands on a scope that's the best way to check the encoder signal. Check the plug inside the electrical box on the spindle motor (power off of course) to verify it is...
  11. Re: Tree J325, Spindle Won't Start, Overloaded Error, Encoder Error on SD

    The -pg error is pulse generator. It is missing some component of the spindle motor encoder signal. The blown fuse can happen for too many max power surges because of the lost encoder signal (it will...
  12. Replies
    4
    Views
    2,811

    Re: Journeyman 325 Tree Mill

    Good luck. Shoot me an email if you need anything else!

    [email protected]
  13. Replies
    4
    Views
    2,811

    Re: Journeyman 325 Tree Mill

    Look up in the taper. Rev 3 has collet with 6 balls and 6mm Allen screw in middle. Rev 2 has a collet with 3 balls and a knock-out button in center past the taper. Rev 1 has 6 pins, 3 each on two...
  14. Replies
    3
    Views
    3,929

    Re: PC2100 Control Alarm 44-84

    Have you gotten this straightened out?
  15. Replies
    7
    Views
    3,267

    Re: TREE 425 CUTTING OUT OF ROUND

    Sorry, late to the party.
    No westamp drives were ever put on J425 machines.

    Balance the lag on the 2100 machines:
    Press DISPLAY
    Select SERVO SETUP, Press the green check mark
    Select a linear...
  16. Replies
    5
    Views
    1,941

    Re: Tree vmc spindle supplier

    Give me a call in the office, 262-758-6129. Ask for bob
  17. Replies
    5
    Views
    1,941

    Re: Tree vmc spindle supplier

    What model machine?
  18. Re: Tree 4024 can't figure out how to set up A axis HELP

    original configuration was rotary windup
  19. Replies
    1
    Views
    831

    Re: tree 840 spindle bearings

    Looks like Monica quoted you the bearings already. Be advised: There are 3 completely different bearing sets in 5 different configurations.
  20. Replies
    5
    Views
    954

    Re: starting wtih TPC-2100 control on 880

    Yup.. welcome to my life. LOL. I actually wrote that procedure specifically for a customer who bought a used 800 from me. The operator just refused to do it per instructions, so I had to make it very...
  21. Replies
    5
    Views
    954

    Re: starting wtih TPC-2100 control on 880

    Another way of doing it:

    Tool and Fixture offset setting on A2100

    Required: gauge block for setting tools. 1-2-3 block or similar. Always use same side

    Tool length setting:
    1. MDI tool into...
  22. Replies
    0
    Views
    782

    2UVR with Erickson QC30 spindle

    Here's a strange request... I had a customer call me a few months ago looking for an Erickson QuickChange 30 spindle for a TREE 2UVR. I scoured high and low but couldn't find anything about it, much...
  23. Thread: spindle drives

    by zpsbob
    Replies
    2
    Views
    575

    Re: spindle drives

    It will do the trick for a little while, but will smoke the drive from overloading
  24. Replies
    8
    Views
    3,155

    Re: Tree journeyman 325

    So this gets archived:

    To make the control on a J325 / J425 go from 3500 rpm to 6000, add a jumper from 24vdc in machine to wire/terminal 238. Most machine the 24vdc can be sourced at the adjacent...
  25. Replies
    4
    Views
    1,567

    Re: Tree 1060 with renishaw probe

    All of us at ZPS-CNC USA handle the support and have since ZPS stopped supplying the machines to TREE. We have done everything we can to make the path for information and support simple, we even...
  26. Replies
    6
    Views
    966

    Re: Tree Journeyman 325 work light

    that's will fit some of the vmc's not the 325. Let me check...
  27. Replies
    4
    Views
    863

    Re: J325 spindle bearings

    Similar from VXB is $423/ea (unmatched). Grainger 836.50/pr. ZPS 552/pr.
  28. Replies
    3
    Views
    1,272

    Re: Tree Journeyman 200r parts

    Which parts are you after? We still have quite a few and if they're "old stock" they're usually bargain priced
    [email protected]
  29. Replies
    55
    Views
    8,619

    Glad its going!! Bob

    Glad its going!!

    Bob
  30. Replies
    55
    Views
    8,619

    Absolutely. What is on the Y and Z motors? Did...

    Absolutely. What is on the Y and Z motors? Did someone move them around?

    What motors are on the axes? Baldor taper shaft? MSI? Baldor straight shaft? They take different pulleys

    Bob
Results 1 to 30 of 60
Page 1 of 2 1 2