509,870 active members
4,260 visitors online
Register for free
Login

Search:

Type: Posts; User: mactec54

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Re: Thanks for the Thread!! Made my decision on which company. NOT FLA...

    GDL do not own or operate any company's in the USA but do have an operation in BC, there are many company's that sell there machines under there own brand name world wide, just like Newcnc in the USA...
  2. Replies
    3
    Views
    9

    Re: vfd mach3 problem

    Could be an easy fix but would depend on how you have the spindle and VFD Drive wired Post some photos and I will tell you what you need to do
  3. Replies
    5
    Views
    505

    Re: flashcut and chinese spindle/VFD

    This is an old thread but for those that don't know a VFD Drive can only be used for a AC 3 Phase motor

    Is your intension to just run the spindle as your VFD can not give you 3Phase power to run...
  4. Replies
    109
    Views
    2,483

    Re: 60" x 40" new build

    Give it a run first it may do all the work you where planning
  5. Replies
    11
    Views
    38

    Re: Mach 3, g28 safe travels height

    So in your Program Drawing where is your Z0. the top of the part or the bottom of the part

    It looks by what you have done here is you have your Z0 at the bottom of your part, this can be a trap...
  6. Re: Start to planning a Bridgeport Series II R2E4 Boss 8 retrofit?

    The DMM is the Best choice for Servo Motors and Drives replacement DMM | Technology Solutions | AC SERVO DRIVE | AC SERVO MOTOR | ROTARY ENCODER

    A Gecko or any Drives like it is not suitable for...
  7. Re: Start to planning a Bridgeport Series II R2E4 Boss 8 retrofit?

    The drives you have will be analog +/-10v, most controls that the hobby area are using Step / Dir control if the old SEM motors are good then there are other controls that can work with the Drives,...
  8. Re: Start to planning a Bridgeport Series II R2E4 Boss 8 retrofit?

    Check the Timing Pulley ratio on the Y axes if it is 2:1 then 750w is more than enough for the Ac Servo motor replacement DMM and Acorn control is also my choice
  9. Re: Spindle stopped during milling YL-620 2.2kW spindle

    What voltage are you using for input Voltage to the VFD Drive ????

    These VFD Drives are not very good and would not buy one even though there are a lot of them out there most have some kind of...
  10. Replies
    109
    Views
    2,483

    Re: 60" x 40" new build

    The 1/2Hp motor is not going to do a very good job on a 30 Taper spindle this normally would have a 3Hp motor on it I don't know why they sold it like this
  11. Re: How to show Rpm instead of frequency? FVD yl620-a

    Set it back to the default=0 and try the DISP again I'm not a fan of this VFD Drive as many users have had problems with them
  12. Re: How to show Rpm instead of frequency? FVD yl620-a

    The DISP should select the RPM, just Press it until the RPM led is on then it will show the RPM

    You could try P00.24=9 this will give you all the options
  13. Replies
    11
    Views
    38

    Re: Mach 3, g28 safe travels height

    Just remove the G28G91 This has no place at the beginning of any program

    And try it like this G0Z0. this should go to your machine Home Zero

    Do you Home the Machine Before you setup your work...
  14. Replies
    61
    Views
    385

    Re: Need help please

    The VFD Drive should be in the Box just as you have built it, anyone that says different does not know what they are talking about, there will always be naysayers that are not capable of building...
  15. Replies
    11
    Views
    38

    Re: Mach 3, g28 safe travels height

    No code attached Just Cut Paste the code, a G28 can be a problem You don't need to use a G28 in any program
  16. Replies
    4
    Views
    13

    Re: Syntec 6MB soft limits

    G54 is your work offset or Start Position X0 Y0 Start Position, when you do you cad / cam program you should set up a frame around your job that is where the soft limits are activated, then you would...
  17. Replies
    109
    Views
    2,483

    Re: 60" x 40" new build

    Normally for low voltage it is connected Delta, this is not a very good motor being 110v don't expect it to have a very good performance if anyone else is buying this make sure it has a 220v/240v 3Hp...
  18. Replies
    16
    Views
    34

    Re: Huanyang 2.2 spindle VFD control

    Post a photo of your wiring

    First check the outputs of the Breakout Board with your meter

    Points to check with your meter 0-10v output from the Breakout board first do a M3S12000 in MDI if...
  19. Replies
    4
    Views
    149

    Re: Laguna Vs Shopsabre vs?

    The post processor is non existent because it mostly will run industry standard G-Code Format

    Here is the G-codes that your control can use, your postprocessor just needs to be changed to suit...
  20. Replies
    4
    Views
    149

    Re: Laguna Vs Shopsabre vs?

    Newcnc https://newcnc.com/cnc-routers/ is worth a look it should be easy to sort out what codes your control likes and does not like Syntec control is a good control, you just have to correct the...
  21. Replies
    16
    Views
    34

    Re: Huanyang 2.2 spindle VFD control

    Yes the jumper should be on VI for 0-10v control or Pin (1 -2 )
  22. Replies
    109
    Views
    2,483

    Re: 60" x 40" new build

    At what voltage it looks like a 3Ph motor is it 220/240 if so a simple VFD Drive will get you going
  23. Replies
    3
    Views
    37

    Re: Linear Rail Mounting method

    Correct it is better if you machine a shoulder for the rail alignment, 2mm is normal but check with your rail you are going to use as the Ground mounting edge are different heights and you need...
  24. Replies
    16
    Views
    34

    Re: Huanyang 2.2 spindle VFD control

    Are you trying to control the VFD with the Pot or are you trying to control the speed with your control software

    What are all the VFD Parameter settings you have set
  25. Re: New Machine Build - Massive CNC router for timber components

    No stress from not welding this is great, but how do you stress relieve the steel parts once it is all glued and bolted together, all the steel parts have stress from it's manufacture, just gluing...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4