584,833 active members*
5,405 visitors online*
Register for free
Login

Search:

Type: Posts; User: timlkallam

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    631

    Re: ALARM "070 NO PROGRAM SPACE IN MEMORY"

    Your memory space is full
    Take out some old programs make room .
    If you trying to download a 1 meg program and your machine only holds 1/2 a meg.
    you have to break you program in half ,run the...
  2. Replies
    8
    Views
    2,004

    Re: Fanuc g54-g59 help please

    use a sub pogram maybe
  3. Re: Colchester Tornado T8 referece point of turret

    I have a clausing with a 21 t control take a picture of the keypad to see if it is the same
    as mine.
  4. Replies
    7
    Views
    765

    Re: Buying stock for 5c collets

    In my opinion Service center brand aluminum is the worst I have lot of bars oversize I can't use.
    The chips don't break very well to gummy ,I avoid it like the plague.

    I have always used Alcoa...
  5. Replies
    8
    Views
    858

    Re: Help Quieting Spindle Down

    I have a Sharp 2412 mill my spindle was getting to the 100db range changed the timing belt now
    its back down to 70db . The belt looked fine also check that the belt is not riding to hard on the...
  6. Replies
    9
    Views
    2,622

    Re: Fanuc OM z axis crash

    There is usually a switch behind the turret .
    If you crash the turret will move and close the switch.
    Nothing will work until you straighten the turret.
  7. Re: Fanuc Oi-TF vs. 31I-B block processing time / speed Is Oi-TF really this slow?

    The math is simple, if 4ms (4 hundredths of a second)

    Isn't 4ms = 4 thousandths of a second.
  8. Replies
    7
    Views
    5,915

    Re: Rigid Tapping not working right.

    I have a Sharp 2412 2005 model this is how I would write it.
    T5 M6 (Tap10-32-HSS-TiCN)
    G0 G90 X3.016 Y-0.8629
    G43 H5 Z.2 M8
    M29S640
    G84 Z-.42 F20.
    G80
    G0 Z3M9
    G53 Y0
    M30
  9. Replies
    1
    Views
    227

    Re: 6061 Barstock Distortion?

    Some times material has stress in it.
    You may need to rough it and leave everything .01 under size
    and let the part sit overnight and then do the finishing.
    I think you problem is with the slot...
  10. Re: Looking for Ideas - Grooving interior Radius

    Dom tube doesn't machine well at all could you use a different material.
  11. Re: lathe programming mastercam to fanuc 21iT

    I have the same control but my machine is storm 80
    I use mastercam also it will put out a lot of unwanted code unless you can change the post
    processor .I never tried to change ours. To complicated...
  12. Replies
    2
    Views
    1,409

    Re: spindle programming error

    I run a lathe with a 21t control also

    G97 S1000 M3 TURNS SPINDLE ON turns at 1000rpm
    G97 S1000 M13 TURNS SPINDLE ON WITH COOLANT

    For constant surface speed you use G92 as a speed limit or...
  13. Replies
    2
    Views
    1,200

    Re: What's the Tornado 100 tailstock taper?

    I have a 1998 clausing storm it has a number 4 taper . Not sure for the Tornado.
    The threads your referring to.There is a nut with a hole in it.
    you screw it on before you put your center in and...
  14. Replies
    11
    Views
    1,906

    Re: CNC Programmer expectations

    I have been a cnc machinist 20 years , I have my own shop and make
    a good living.
    Not near the ability you have just lathes and mill no 4 and 5 axis.
    I can honestly say i have never written a...
  15. My girlfriend had the exact symptom's you have ....

    My girlfriend had the exact symptom's you have .
    Tried antibiotics nothing worked coughed day and night no relief . Doc took cat scan had a spot in the lung
    then a biopsy of the lung
    and it was...
  16. Replies
    1
    Views
    4,186

    G92 is used with constant suface speed (G96 )as a...

    G92 is used with constant suface speed (G96 )as a max speed limit. Or as a work shift .

    Lets say you you have a 6 inch dia. part to face and you want to use constant surface speed( CCS) of say...
  17. Replies
    2
    Views
    226

    Oo123(main program) EXAMPLE T0101 S2000M3 GOX2...

    Oo123(main program) EXAMPLE
    T0101
    S2000M3
    GOX2
    M99
    Put M99 at end of the main program instead of M30

    Write separate up program this is called the sub program

    O0345(sub program)
  18. PPC metals phone 704-283-9122 they can do...

    PPC metals phone 704-283-9122 they can do everything you asked in your post .
  19. Replies
    1
    Views
    797

    Have you checked the H limit on the tap If youre...

    Have you checked the H limit on the tap
    If youre in g95 mode your code is correct
    If in g94 the feed should be F20
  20. Replies
    5
    Views
    1,788

    Max I don't think you understand . You didn't...

    Max I don't think you understand . You didn't lose your parameters you lost the absolute encoders position. First buy a new battery when you open the machine cabinet its about chest high goggle the...
  21. Replies
    5
    Views
    1,788

    What has most likely happened is you axis...

    What has most likely happened is you axis battery's died they only last 2 years. They keep power to the encoders when the machine is off so it won't lose it position.
    The parameter battery's last...
  22. Replies
    11
    Views
    1,593

    Hello James , Brazing the shank on and expecting...

    Hello James , Brazing the shank on and expecting it to run true never did work.
    So now we braze on the shank and then machine it holding the shank
    in a collet.

    I have found checking for runout...
  23. Replies
    8
    Views
    1,410

    SHARP 2412 TOOL CHANGE MACROS % O9001...

    SHARP 2412 TOOL CHANGE MACROS

    %
    O9001
    #3003=1
    #3004=1
    IF[#100EQ#4120]GOTO99
    IF[#4120EQ0]GOTO99
    IF[#1011EQ1]GOTO99
    G91G28Z0.
  24. Put an indicator in the chuck tram the inside of...

    Put an indicator in the chuck tram the inside of the drill holder move x using the mpg until it is centered and that will be X0 for your drill.
  25. Drills and taps are set at x0 Tram your drill...

    Drills and taps are set at x0 Tram your drill holder get it exatly centered push measure key type in x0 then press measure key .

    example to drill a 1 inch hole 2 inchs deep
    T0101(1 INCH DRILL)...
  26. Tool seting fanuc 21 To set work shift move...

    Tool seting fanuc 21

    To set work shift
    move the tool to to your zero point( touch off tool 1 in program)
    press off set key
    press right arrow soft key TWICE( the soft keys are under the screen...
  27. Replies
    5
    Views
    1,323

    I have a sharp 2412 it doesn't uses much air you...

    I have a sharp 2412 it doesn't uses much air you should be fine .
  28. Replies
    3
    Views
    707

    12l14 need about a .01 to.02 inch depth of cut to...

    12l14 need about a .01 to.02 inch depth of cut to get a good finish.A light cut seems to tear the materal insted of cutting it.
  29. Thread: need help

    by timlkallam
    Replies
    5
    Views
    700

    Go into cimco setup and put 50-100 mili seconds...

    Go into cimco setup and put 50-100 mili seconds pause between blocks . Your computer is sending code to the machine faster than it can handle.
  30. Replies
    23
    Views
    3,931

    Hello Travis , For setting the X and Y axis move...

    Hello Travis , For setting the X and Y axis move the table where you want X0 and Y0 to be .

    Go to the offset screen highlight X under G54 key in X0 and press the measure key ,its the soft key...
Results 1 to 30 of 231
Page 1 of 8 1 2 3 4