Search:

Dear Experts
I have two faulty hurco yaskawa spindle drives.one drive shows "01" error and another shows "d1" error
both faults are in control card. i want to repair these drives. any person can...

Dear Experts
i have following files in floppy and i want to know which software will be use to open these files.
FP80.Z32
804B153.Z32
MERKER.Z32
MFP5DC.Z32
MFPA.Z32
CNCSYNDC.Q32
OVERRIDE.Q32...

Dear Experts
I have CIMR-M5A20150-XXXD spindle drive installed and it is in faulty condition.now i want to purchase new drive. supplier is offering CIMR-M5A20150-XXXH model so i want to know the...

Dear Experts

I have 6T-Model B Control system. When I entered PC parameter it accepts all editable parameters. But when machine restarts all PC parameter return to their default values. I mean...

Dear drdos
Yes Data Server is in storage mode but still same issue.

Dear dcoupar
I did this in RMT mode but DNC-ST option is not visisble

Dear Experts

We have a Fanuc 18iMb Control System with DATA SERVER CARD option and we need to execute the programs from HD-DIR.

We have set the below mentioned parameters.

1- MDI Mode
2-...

Dear Experts
I want to interface my laptop with iTNC 530 by using TNCremoNT software. i want to make complete backup of control. there is no MOD function button is available in my control keyboard...

Dear Experts
I have Deckel Maho DMU80P with heidenhain TNC426 Control. The display is not showing anything only screen flickering. i have checked all power supplies on lcd board.+5V +3.3V is ok....

Dear Experts
Nobody give me the answer and i find out myself. i find out that spindle encoder is faulty. i replaced the encoder and fault is remove. when installed encoder must check 1 Vpk-pk...

Dear Experts
Please reply where can i download TNC426 complete service and maintenance manual

Dear Experts
I need Heidenhain TNC426 complete technical and service manual. i want to check Spindle encoder by using parameter. because my heidenhain control is showing S173+ error on control it...

Dear Experts
I have Deckel Maho DMU80P Machine and it is showing error S173+. now please tell me the solution.

Dear Experts
I want to online with my HURCO VTXU PLC.send me the procedure. i have winpc32 software installed on machine.

Dear Experts

I am using DNC option via serial RS-232.. How can i use DNC function through Ethernet.

Dear Experts
We have Index GU800(Germany) Lathe Machine. We are facing a problem that when we run the machine in rapid mode, the axis speed runs fine by 20%.But whenever we increase the feed rate...

Dear Experts
We have Index GU800(Germany) Lathe Machine. We are facing a problem that when we run the machine in rapid mode, the axis speed runs fine by 20%.But whenever we increase the feed rate...

Thankyou very much for your details replays..

The machine working well but after 10~20 mins x-axis gives noise and vibration and also motor starts vibrates but not feels like heating up... some...

Motor is not heat up. but there is too much vibration in motor only when fault occurs otherwise motor is normal. and there is no Excess load on axis. sometimes motor vibrates and automatically go to...

Just turning on the machine all is ok. when program starts and machine is running after 3 to 4 minutes these fault occurs.

can you also give comments about under mentioned error codes. are these seem like drive error or any other.

Alarm 436: n-Axis Soft thermal OVC: The digital servo software detected the soft thermal...

Dear jjautomation
Thanks for your reply. i have same amplifier but it is different machine which is configured with different parameters. so please send me the procedure how i can change this...

Dear Experts.
I have LeadWell LTC35CLM Machine. my program is working fine and after 3 to 4 minutes a terrible sound occurs in machine and X-Axis Load Bar Shows Full on Display. when i check then i...

Whenever we try to take SRAM backup or try to restore the backup,we get the error "memory card do not exist" or "memory card write protected."
But The same card is working fine when running for the...

I have Deckel CNC Milling Machine. Model FP4AT Dialog 11 Control.
We are facing problem, that G0 and G1 commands are not working.

Machine is working well in manual mode means
Manually all axes...

I have Deckel CNC Machine. Model FP4AT Dialog 11 Control. i have a problem that G0 and G1 commands are not working. Machine is working in manual mode means manually all axes are working fine. home...

Dear Experts
I have a Lead Well Lathe Machine Model No.LTC35CLM with FANUC Oi-Tc Model. Yesterday i see a faults:

Alarm 1003:Turret Miss-Index(A0.3).

Alarm 1011:Turret Not Orientation(A1.3).
...