501,705 active members
7,712 visitors online
Register for free
Login

Search:

Type: Posts; User: CATCH22

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    98

    Awesome, thanks Sean.

    Awesome, thanks Sean.
  2. Replies
    14
    Views
    98

    Hey Sean where did you get the stuff to make your...

    Hey Sean where did you get the stuff to make your own boards?
  3. Replies
    14
    Views
    98

    Thanks Sean, now all I have to do is figure out...

    Thanks Sean, now all I have to do is figure out how to read electrical schematics. Lol
  4. Replies
    14
    Views
    98

    Hey Sean, I would like a drawing of your...

    Hey Sean, I would like a drawing of your electronics if you wouldn't mind, I could possibly copy it to get mine setup.
    Thanks Mike
  5. Replies
    14
    Views
    98

    OK so I got everything wired up and all the...

    OK so I got everything wired up and all the switches on the drive set but it is still giving me the red fault light.

    TB5 GRD to REF-
    TB5 AOUT to REF+
    TB5 ENABLE+ to INHIBIT
    TB5 ENABLE- to GRD...
  6. Replies
    14
    Views
    98

    OK thanks very much.

    OK thanks very much.
  7. Replies
    14
    Views
    98

    Setting up AMC BE25A20 in torque mode?

    Can anyone help me out, I'm trying to setup Linuxcnc with Mesa 5i25 and 7i77 and AMC 25a20 servo drives, I'm told it's easier and better to have the servos run in torque mode, but I can't seem to...
  8. Replies
    78
    Views
    454

    So from what I have been reading I don't use the...

    So from what I have been reading I don't use the tach at all, it just uses the glass scales for positioning.
  9. Replies
    78
    Views
    454

    Should I setup the servos in torque mode or...

    Should I setup the servos in torque mode or velocity mode, from what I have been reading torque mode is easiest and is a bit tighter. And I also uploaded a drawing if you could have a quick look at...
  10. Replies
    78
    Views
    454

    Hey Jim, do I keep using the inductors for each...

    Hey Jim, do I keep using the inductors for each axis.
    The purple and blue wires are the power wires to the inductors. Then to the servo motors.
  11. Replies
    78
    Views
    454

    OK thanks a lot Jim, I really appreciate it.

    OK thanks a lot Jim, I really appreciate it.
  12. Replies
    78
    Views
    454

    Here are 2 pics of the drives.

    Here are 2 pics of the drives.
  13. Replies
    78
    Views
    454

    OK so I pulled the original drives and I'm going...

    OK so I pulled the original drives and I'm going to start wiring the new AMC BE25A20 drives, they are brushless drives but I setup the switches on the drive to run brushed servo motors. Now I need to...
  14. Replies
    78
    Views
    454

    OK thanks Jim, I guess I will start installing...

    OK thanks Jim, I guess I will start installing new drives this weekend.
  15. Replies
    78
    Views
    454

    OK before I go switching to the other drives I...

    OK before I go switching to the other drives I found this servo circuit board drawing, if this does not have the information I need then I will switch drives.
    Thanks Mike
  16. Replies
    78
    Views
    454

    Would I be better off going with the AMC 25A20...

    Would I be better off going with the AMC 25A20 drives I have, I just thought it would be easier to just use the original drives for now because I don't have a clue what I'm doing. Lol
  17. Replies
    78
    Views
    454

    I can't find a J1 anywhere, but here is what I...

    I can't find a J1 anywhere, but here is what I think you are looking for.
    Thanks Mike
  18. Replies
    78
    Views
    454

    Anilam Crusader M control. Servo Drives EG&G...

    Anilam Crusader M control.
    Servo Drives
    EG&G Torque Systems servo drive
    Model number ACU3015-100D
    Can't find any documentation for these but I do have original wiring diagram.
  19. Replies
    78
    Views
    454

    Is there a wiring drawing I can find that shows...

    Is there a wiring drawing I can find that shows the proper way to do it with the 5i25 and 7i77 on a 3 axis mill?
  20. Replies
    78
    Views
    454

    Oh ok, I guess I will have to do some more...

    Oh ok, I guess I will have to do some more research on that.
    Thanks PCW
  21. Replies
    78
    Views
    454

    Re: Anilam crusader m control problem.

    And I'm assuming that will all be done using pncconf.Is that correct?
  22. Replies
    78
    Views
    454

    Quick update, just got home from work and turned...

    Quick update, just got home from work and turned the mill on, the servos have power to them and all are turning very slowly, so I hope this means my Mesa boards are fine.
  23. Replies
    78
    Views
    454

    OK I will see what I can find for a manual. ...

    OK I will see what I can find for a manual.
    Thanks Mike
  24. Replies
    78
    Views
    454

    Thanks Jim, I just uploaded a picture of the...

    Thanks Jim, I just uploaded a picture of the lights on the drive, VE EC GF SC are what it shows next to the lights.
  25. Replies
    78
    Views
    454

    Maybe this will help.

    Maybe this will help.
Results 1 to 25 of 240
Page 1 of 10 1 2 3 4