502,889 active members
5,157 visitors online
Register for free
Login

Search:

Type: Posts; User: TomKerekes

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Re: Need a way to copy KFlop flash memory to create a duplicate board

    Hi raasco_alan,

    We don't have a method of transferring programs without the source.

    I suppose you could write a program to write out the Thread memory spaces as binary bytes then read them back...
  2. Re: Can Kanalog be used as a source vs sinking for relays.

    Hi George,

    I dont follow all that but it seems the Glentek "lockout" signal itself can be driven with only 3ma. So you might conider removing the relay and driving it diectly with a Kanalog Opto...
  3. Re: Can Kanalog be used as a source vs sinking for relays.

    Hi George,

    No. The Kanalog Relay Driver Outputs can only sink to GND. They can not source voltage.

    If the Relays take less than 25ma a Kanalog Opto Output could work.

    Consider adding a...
  4. Replies
    9
    Views
    69

    Re: auto tool change on axis A

    Hi vektor_z,

    I don't really understand what you are doing or what the issue exactly is.

    But after homing maybe you need to do something like:

    persist.UserData[LAST_TOOL_VAR] = 1; //set...
  5. Replies
    319
    Views
    14,942

    Re: Tree325 Retrofit Started

    Did it show Connected? Did KFLOP have power? What error did you receive when pushing Initialize ?

    ok

    Did what a few times? Power cycle? Was it necessary?

    What error? Does it seem to be...
  6. Replies
    319
    Views
    14,942

    Re: Tree325 Retrofit Started

    Hi Peter,

    I don't see why you think following errors are the problem. A following error shouldn't cause the USB to disconnect.

    What exactly are you doing? Are you able to initialize and do...
  7. Re: Can’t turn on axis (after turn off machine during G-code)

    Ha ha. Thanks for taking the time to post back.
  8. Re: Can’t turn on axis (after turn off machine during G-code)

    Hi RuslanRobot,

    Both programs have a loop disabling axes 0-3 if virtual bit 1024 (ESTOP) is not 1. See a fragment of your code below:



    #define ESTOP_BIT 1028

    // if ESTOP present...
  9. Replies
    6
    Views
    52

    Re: Kflop driver failed

    Hi Jack,

    Great. Thanks for taking the time to post back.
  10. Replies
    6
    Views
    52

    Re: Kflop driver failed

    Hi Jack,

    Strange I just Uninstalled then Updated the Drivers on my Windows 10 64-bit V1903 system without any problems.

    It is normal that KFLOP shows up in "Other Devices" without the Driver...
  11. Replies
    6
    Views
    52

    Re: Kflop driver failed

    Hi Jack,

    The drivers in Release Version 4.34 should work with Windows 10.

    You should navigate to th USB Driver folder not the i386 folder.
  12. Replies
    9
    Views
    69

    Re: auto tool change on axis A

    Hi vektor_z,

    Support of metric Tool Table values was corrected in Version 4.34k (1/13/2018). Please try Release Version 4.34 or later.



    You can use these GCodes:

    G43 Hn (Tool #n length...
  13. Replies
    9
    Views
    69

    Re: auto tool change on axis A

    Hi vector_z,

    The servo settings and Tool Table are different. Why can't you enterthe Tool Table values in mm to match your Job and DROs?

    What version are you using? There was a bug regarding...
  14. Replies
    1
    Views
    34

    Re: Entry Point Not Found Exception

    This was a duplicate post and was answered here.
  15. Replies
    9
    Views
    69

    Re: auto tool change on axis A

    To turn on tool lenght/offset compensation use G43

    G43 Hn (Tool #n length comp On)
    G43.4 Hn (Tool #n length On with RTCP On)


    The Tool Table Lengths and Offsets don't have units. They are...
  16. Thread: MAHO 600E

    by TomKerekes
    Replies
    53
    Views
    3,100

    Re: MAHO 600E

    Hi swat cat,

    Where did you get the post processor?

    Maybe ask Autodesk?
  17. Replies
    9
    Views
    69

    Re: auto tool change on axis A

    Hi vector_z,

    I'm not entirely sure I understand your configuration. Each spindle uses both ends?

    You should be able to shift the A Axis machine origin based on Tool Number with the following: ...
  18. Thread: MAHO 600E

    by TomKerekes
    Replies
    53
    Views
    3,100

    Re: MAHO 600E

    Hi swat cat,

    There isn't a function to read the SSO value. There is a function to set the SSO from KFLOP:

    DoPCFloat(PC_COMM_SET_SSO,SSO);

    If you are setting the SSO from KFLOP, for...
  19. Replies
    1
    Views
    47

    Re: Transfer settins

    Hi Evg_4,

    The KMotionCNC Tool Setup parameters are saved in the file <>\KMotion\Data\GCodeConfigCNC.txt

    If any other files were changed it is simplest to copy the entire <>\KMotion\Data...
  20. Re: Taig CNC-Controller Replacement-Dynomotion Suggestion

    Hi Peter,

    No it doesn't. It's a power thing not a current thing. Please read this article.
  21. Thread: MAHO 600E

    by TomKerekes
    Replies
    53
    Views
    3,100

    Re: MAHO 600E

    Hi swat cat,

    There isn't currently a method of accessing the S value. Only the desired speed.

    Couldn't you use the initial desired speed to decide which gear to use?

    Maybe use an MCode to...
  22. Re: Taig CNC-Controller Replacement-Dynomotion Suggestion

    H iPeter,

    Those look good to me and others have used them. Expect maybe 400RPM with a 48V supply.

    I prefer regulated switching supplies. They are regulated and lower cost.

    This should work...
  23. Replies
    2
    Views
    55

    Re: I can not recover kflop.

    Hi mk00,

    Maybe you are performing the recovery steps incorrectly? Follow the procedure here.

    If still not recovering describe the steps you are doing and what happens.
  24. Re: Taig CNC-Controller Replacement-Dynomotion Suggestion

    Hi Peter!

    After your complex servo system a stepper system should be a cake-walk for you :)

    You might watch our KStep Introduction Video:


    https://youtu.be/pW-9fDLAn2s

    Tutorial here.
  25. Re: Invert signal from end sensor. Appointment signal as the emergency stop button.

    Hi RuslanRobot,

    Specifying a Stop Action allows you to do something extra when the Operator pushes the on screen stop button.

    You need the C Code to be running continuously and before the EStop...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4