Hey thanks... That s also a good idea to quickly make a find and replace...
I have tried to look at the post processor but since I am no programmer, I got lost very quickly haha :).
I would...
Type: Posts; User: d3workz
Hey thanks... That s also a good idea to quickly make a find and replace...
I have tried to look at the post processor but since I am no programmer, I got lost very quickly haha :).
I would...
Hi,
I just finished my DIY CNC table and tried my first cuts.
My issue is that the M5 command gets active before the cut is fully ready. I have done a test by manually adding a delay time...
Hi guys,
Is it possible to add Gcode in Fusion360 in a specific way though (not adding a pass though from the manual NC)!! I need to add a G4 P2. after every M5 that I have?
I am using Fusion...
Please excuse me, as the first post was done in a hurry and it does not make sense... so here goes again:
Hello guys
Is there someone who has successfully connected a torch height controller...
Hello guys
Is there someone who has successfully connected a torch height controller (THC) with the NVUM v2 controller?
I was looking at the Proma SD model, but it seems that the Proma works...
Hi again guys....
I fixed the problem and I am writing here so that if someone ends up in my situation, I would maybe help or shed some light.
The issues with the NVUM board is that the OUTPUT...
Hi.
Before I jump to my problem, I have to say that I have used various cheap BOB, which cost less than €25, and never had issues....
Now to my problem... so this time I wanted to get a more...
Thank you very much for your reply.
SO now I am more confused! This is the thing, I have two machines (both DIYs), one CNC mill other CNC plasma. On my mill, every time I turn it ON, I home all...
Hi again,
I am still trying to figure out how to get Mach 3 to auto toggle the soft limits after the Ref all is completed!!! Like I said I am no programmer, however from what I read I would like...
Hi ppl.
Today I just notice that on my plasma machine, when I refernce all axis to home, the softlimits do not toggled on automatically! However, on my cnc mill, this gets activated automatically...
Thanks again for your thoughts.
Btw yes I do recommend longmotors, I have them on the cnc mill/router what ever, and my cnc plasma (which is 1.3m x 2.5m cutting area). Love their stuff... ...
Phxeww... at least you thought of it!!!, because for a minute there I thought it is still something not to consider.
I understand what you mean about the cleaner look, but my case is much simpler...
If I may ask you, just out of curiosity, why didn't you leave the nema 34 and consider a reduction on the motor side... I am sure that these Nema 34 will not run out of torque if kept under 500 rpm.?
Hi rodw, thank for your comment.
Can you please elaborate a bit more about what you meant that there is a mis-match between the motor size and the application? As I am not sure what you meant.
...
This is the torque chart of the Nemas I am using.
Thank you for your thoughts Ger21.
I am glad that you think this may be the issue as well. Before I go and spend more money on bigger supplies, I am waiting for some 48T pulleys and belts, so...
Thank you for your comments guys...
I think I found the problem... still not sure though. I think my problem lies in my gear ratios between the motor and lead screw. I have lead screws of 5mm...
Hello to all of you gurus again.... I was hoping that by now some would have shed some light here... but understand that me post is all over the place... and that is how I feel.
I think what I...
Hi to all, I am new here.
I have 2 cnc machines, one is a plasma table (nearly ready but operational) and I have a CNC mill with a 2.2kW router. Both are diys and the latter one I had it for over...