Search:

Thanks Ger 21 problem solved.

Thank you, I'll try them this evening.

Well Ger 21 you're right, that's the version I'm running. So I need to find an older version? If so can you direct me, I would appreciate it.

LeeWay, Thanks for the reply.
I did change the Safe Z with no change. Maybe the setting are not what they should be. I'm on machine coordinates.
I can change the tool and have it register it's...

I got Big Tex's new script and have a problem with it. I followed the instructions in the video. I the initial setup button works as shown.The zero tool setup button seems to be caught in almost a...

I got Big Tex's new script and have a problem with it. I followed the instructions in the video. I the initial setup button works as shown.The zero tool setup button seems to be caught in almost a...

I found the answer.

Was it something I said? Is there not enough info to start a conversation? I posted this almost a year ago, and I still have'nt gotten any where. Could someone please throw me a bone.

Karloterrazas

I have a DMB4250-8B and have installed a Super PID. I have not yet got it to work. Have you got any luck since you posted this?


nytwin1

I contacted DMM tech, and this is what they told me.
I'm not very familiar with the super PID board, but it looks it can be run independently without the use of our controller board.

From their...

Yes. I have pin #16 wired to Super PID to turn it on and off.
I have changed the rpms to 30,000, to be correct.
Still no change.

I guess correctly is a relative term. PWM is 200 & 0 the pulley is set at min: 0 max: 25000 ratio: 1
I hope I attached the PDF correctly. It shows the setting required by the board manufacturer. ...

Hello again gentlemen,
I have hooked-up a Super PID to my DMB4250-8B brakeout board. I can get it to run manually. With the MDI using Mach3 I only can get 5000 rpms no matter what spindle speed I...

Hello gentlemen,
I have hook-up a Super PID to my DMB4250-8B brakeout board. I can get it to run manually, but not with MDI using Mach3. My solder jumper is set to PC. I have wired it up the...

Mactec54
I solved the problem not the exact way you suggested, but you gave me the idea.
The SS has 2 ports, and I had a C10 board form CNC4PC. So I connected it and added some power. Then with...

Mactec54
I've not gotten a chance to checkout the pin settings you are referring too.
I don't remember any pin settings when setting up the SS. Here are some pics of my setup.
Remember wiring...

Mactec54
Could it be because I'm using a smoothstepper card before the breakout board?

Nytwin1

Mactec54
I first have to say I'm electricly challanged. I got the 4.7ohm resistors and tried the
setup as you suggested. I got no results. I did have 5 volt LED and touched both grounds
for JP5...

mactec54

Any help would be greatly appreciated.

Thanks.


nytwin1

Mactec54,
I'm using a DMM xml file, but believe you are mistaking my board for the other one they sell. Mine is the cheaper of the two. I'm not using an "A" axis. My E-stop is pin 10 works well....

I have a machine that runs well. I would like to get the Z probe function working to complete the machine's ability. I have the programming seeming to work correctly. It will run, and if the plate is...

Montabelli, how would you use a pneumatic cylinder for a brake on Z? I'm not able to picture this. Could you, please explain.

Slowleaner, I have a 1.5 HP router at the moment. My machine is a bit bigger then a table top. Cutting surface 19 X 28 I'm upgrading the machine to help with all of the other projects I have going.

Gentleman,
Thank you for the quick reply, and the information. I have now tested the Z motor under no load. "NO HEAT" It surprised me. For 1 hour the machine was moving up and down. There was no...

The machine is about 15 years old. The original motors were stepper. I put DMM AC servo motors on all 3 axis. I can't keep the Z axis from falling to the table. This happens when the power is turned...