584,817 active members*
5,140 visitors online*
Register for free
Login

Search:

Type: Posts; User: PNaedele

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Re: 401 servo alarm (VRDY OFF), at turn on, Fanuc OM SOLVED

    Next time you get this alarm, check the servo amplifiers in the control cabinet for an alarm number on the 7 segment LED. This should help narrow down what the actual problem is.
  2. Replies
    4
    Views
    2,180

    Re: HAAS VF7 SPINDLE OVERLOAD 200% HELP

    Is the spindle driven by a belt? We had a little Mori that had most of the small V Belts come apart and it had trouble reaching speed and had no cutting power.
  3. Re: Monitor is repeating same message and is unresponsive

    Maybe try playing with the pots on the back of the tube. It's been a while, but VHOLD or VSYNC. Maybe the flyback transformer is going out? I've never replaced one, so that's as much as I know.
  4. Replies
    1
    Views
    514

    Re: lubrication watch dog alarm

    Sometimes there are several timers associated with the automatic lubricator in the ladder. The ladder is programmed in a way that will read the state of the pressure switch several seconds after the...
  5. Replies
    4
    Views
    1,017

    Re: Mori Seiki SV-500

    This sounds like a power supply issue. The problem will be which one.

    Check optional equipment. Could be something is leaving the EStop circuit open until it starts up. Like the spindle chiller.
  6. Replies
    8
    Views
    1,409

    Re: getting copy of Fanuc ladder

    When I punched out the ladder on one of the machines I take care of from the I/O in PMC, the file is an ASCII representation of HEX data.

    The ladder is stored on an EPROM and I thankfully haven't...
  7. Replies
    3
    Views
    792

    Re: FANUC 16mb axis problem - 414 alarm.

    The machines I've experienced 414 alarm errors on, the servo amplifiers, servo encoder, motor or motor cabling were defective.

    Diagnostics 200, etc. plus the LED alarm on the servo amplifier help...
  8. Replies
    4
    Views
    1,061

    Re: Parameters affecting M00 and M02

    Our Doosans have different behaviors like that can be changed from the Keep Relays.

    I'd check the documentation for the machines.
  9. Replies
    7
    Views
    1,827

    Re: Problems with DM4500 with Meldas M3

    I'm curious to hear what you have found out about the magazine controller. I have a friend with one of these machines and I've recently helped him recover it from losing it's memory. Besides the...
  10. Replies
    4
    Views
    1,713

    Re: Formatting CF Card in CNC/PC

    Try searching your desktop for 'Creating and Formatting Partitions'

    Then see if your flash drive is listed. I've had the best luck on Fanuc controls when you format a single partition to 256MB...
  11. Re: Help recieving and transmitting files to Fanuc 6M

    Make sure O1001 doesn't already exist in memory.

    I just hit [READ] in Edit mode and the

    %
    :1001
    ....

    or
    %
  12. Replies
    1
    Views
    552

    Re: Fanuc 0i-m problem

    It wasn't an 0i-M but a 16M that I needed to manually input the settings for communication as well as the 9000 parameters. I'll never be sure why it refused to read RS232 until I entered the 9000...
  13. Replies
    3
    Views
    785

    Re: Mori Seiki SL-153 Fanuc 18i TA

    This sounds like a power supply issue for the servo amplifier. It may need to be repaired or replaced.

    I've found with the machines I work on that begin having problems, if I leave the main...
  14. Replies
    9
    Views
    691

    Re: Fanuc 180i won't boot

    This looks like possibly an issue with the Windows boot loader?

    I'm not sure on the steps, but maybe try to repair the installation with a Windows startup disc.
  15. Replies
    2
    Views
    423

    Re: Z axis issues when homing for ATC

    I agree with this. I had a machine with incremental encoders and home position was set by switches and dogs that had a home a couple inches off after I rotated the ballscrew by hand. I forget what...
  16. Re: Question about AC servo motor type Alpha C

    If you have a megger or a multimeter that can check up to 60 Megaohms, check resistance from a phase to ground. A megger is better for this, but a multimeter will detect and obvious problem with...
  17. Replies
    2
    Views
    1,668

    Re: 4th axis question

    Probably prm 3134
  18. Replies
    7
    Views
    2,347

    Re: Fanuc OTc 414 X axis detect error alarm

    I don't have a Fluke 87, but both an inexpensive insulation resistance tester and inexpensive multimeter with much of the same functionality as a Fluke 87. My multimeter seems to be accurate enough...
  19. Replies
    7
    Views
    2,347

    Re: Fanuc OTc 414 X axis detect error alarm

    How were the motor power cables checked?
  20. Re: Does anyone need service manuals for popular Doosan Machines?

    It works.
  21. Replies
    27
    Views
    35,524

    Re: (ALARM 414 SERVO ALARM) Y-AXIS DETECT ERROR?

    I had alarm 8 on a couple different machines. Most likely a transistor module blew up if it's alarming all the time. The big question is why did it blow up.

    Unplug the power cables to the servo...
  22. Replies
    16
    Views
    4,192

    Re: Makino fnc 106

    Looks identical to mine. I've noticed that you may have to click the switches just right. In '99' the LEDs scroll from 0 to 7 if everything is right. There are also LEDs in the back of one of those...
  23. Replies
    4
    Views
    1,191

    Re: Threading on CNC Lathe no longer working

    I don't know if a slipping belt would also cause this problem.
  24. Replies
    16
    Views
    4,192

    Re: Makino fnc 106

    Looking through notes, perhaps Parameter 1 bit 0 is simultaneous control of 4th axis and has to be '0' as well.

    I'll try to find out if my magazine controller diagnostic manual also has a section...
  25. Replies
    16
    Views
    4,192

    Re: Makino fnc 106

    Use this information at your own risk as I got this from an FNC 128 and I don't know if this will work for you.

    Parameter 1, Bit 1 as '0' to disable 4th axis.

    Again, I don't know how different...
  26. Re: Dyna Myte 4400M with Meldas M3 Control. I think the battery is dead

    I'm helping someone out with a DM4500 I think.

    Seems to be the same control and very similar machine all together.

    He had the same issue with the battery, but thankfully he had backups and I...
  27. Thread: SVC-A board

    by PNaedele
    Replies
    1
    Views
    575

    Re: SVC-A board

    I think I had this happen with several boards getting killed on a couple Cadet V4020 OSP 5200s.

    I had to send the damaged servo amps and motor to be repaired on request of the Hartwig tech. He...
  28. Replies
    7
    Views
    3,230

    Re: Cleaning Linear Glass Scales

    We had a scale that was flooded with compressor oil from an overflowing air filter bowl. Purged the lines with alcohol and clean air then used a quick drying electrical contact spray on the scale and...
  29. Replies
    6
    Views
    2,205

    Re: FANUC Series 18i-MB CF Card Problem

    I had to partition my card to 256 MB and set as the active partition before I was able to use it on the IPL screen.

    You may also need to name the volume 'FANUC LTD' as you format it as FAT 16.
  30. Fanuc 18iMB program display while running subprogram from memory card

    Hello all.

    The machine is a Doosan horizontal milling machine with an 18iMB control.

    I've noticed sometimes while a subprogram is running from a memory card, all lines but the current and next...
Results 1 to 30 of 52
Page 1 of 2 1 2