584,871 active members*
5,191 visitors online*
Register for free
Login

Search:

Type: Posts; User: GORDYKD

Search: Search took 0.00 seconds.

  1. Toolmex TUR630MNN lathe PLC failure/ replaced now odd action

    Toolmex Manual Turn lathe with 840D is not operating correctly. Had a PLC failure and had to replace it and reload the software. We lost our programs during the process.
    The issue is that as we...
  2. Toolmex TUR630MNN lathe PLC software/ladder needed

    Hi All,
    I have a Toolmex lathe made by HACO/FAT model TUR630MNN SN. 060593
    The PLC took a crap (Siemens S7-300) and I don't have the archive files to reload.. So far I have not been able to get...
  3. Replies
    7
    Views
    1,669

    Re: Teachmotion probe data edit

    Thanks Tom,
    Now it's starting to make sense. The table expects a constant increment for the data, probably determined by the initial data points.
    I will take a look at the source code. I have not...
  4. Replies
    7
    Views
    1,669

    Re: Teachmotion probe data edit

    Tom,
    Are you saying that the data points saved in "probedata.txt" are not actually used for the teach motion, there is a "table" elsewhere that it follows? I have not seen "delta" displayed...
  5. Replies
    7
    Views
    1,669

    Re: Teachmotion probe data edit

    The problem is that when it gets to about X -15.00 the tool starts pulling away from the profile. The display shows the intended profile correctly and the tool will not get close to it after that...
  6. Replies
    7
    Views
    1,669

    Re: Teachmotion probe data edit

    Hi Tom,
    The die is a fairly simple shape, similar to a cooking pot. It has a radius at the end(pot bottom), a long straight section(pot side), and a flange at the other end(pot rim).
    In trying to...
  7. Replies
    7
    Views
    1,669

    Teachmotion probe data edit

    I have a die that I probed in two stages and attempted to merge the two files. The line generated in the teachmotion and in the NC corrector file looks perfect. The problem is the tool will not...
  8. Re: Using Microsoft Sidewinder Force Feedback 2 joystick

    We have used the wireless Logitec gamepad without any connection issues, but the sensitivity for machine control is not what we were looking for. The little thumb button did not give the operator a...
  9. Re: Using Microsoft Sidewinder Force Feedback 2 joystick

    Hi Tom,
    Thanks for the reply.
    Occasionally get an error " read failed auto disconnect" which appears to be a loss of USB communication to the control.
    We have tried the Microsoft Sidewinder 2,...
  10. Re: Using Microsoft Sidewinder Force Feedback 2 joystick

    We have tried several different non feedback joysticks and there seems to be a communication conflict with the CNC controller.
    What are your thoughts on how the teach mode can be used if no...
  11. Re: Using Microsoft Sidewinder Force Feedback 2 joystick

    Interesting, as you recommended this particular joystick in an earlier post.
    https://www.cnczone.com/forums/dynomotion-kflop-kanalog/379038-force-feedback.html#post2292222
    It does seem to attempt...
  12. Using Microsoft Sidewinder Force Feedback 2 joystick

    I am trying to use the joystick for better control over the Logitech gamepad that was previously being used and add feedback to the teach mode. So far the operation seems erratic and even crashes...
  13. Replies
    5
    Views
    1,128

    Re: Force feedback?

    Good morning Tom,
    This is a metal spinning operation and the operator is having great difficulty teaching the control because he can't feel the force as he is used to with a manual machine. There...
  14. Replies
    5
    Views
    1,128

    Re: Force feedback?

    Thank you for the reply. Sorry for the long delay in response. I am mainly interested in being able to feel the force applied by the machine servos. Is that possible?
  15. Replies
    5
    Views
    1,128

    Force feedback?

    Is anyone using haptic or force feedback during teach mode? If so please describe your hardware and setup.
  16. Replies
    1
    Views
    879

    joystick ortions

    Has anyone tried different joysticks for a better control curve on manual manipulation of the axes? If so what can be used?
  17. Replies
    15
    Views
    1,460

    Re: unintended opto output during boot

    He still doesn't get it.

    Below is a little of the latest correspondence.

    Been three weeks since he promised to send additional components to correct some of the issues.
    I have finally...
  18. Replies
    15
    Views
    1,460

    Re: unintended opto output during boot

    Thanks for all the replies. I will be modifying the control circuits to incorporate these safety measures. The big challenge will be convincing the designer/builder that it is actually his...
  19. Replies
    15
    Views
    1,460

    Re: unintended opto output during boot

    Al,
    Unfortunately with the abundance of inexpensive control systems and components, anyone with a rudimentary understanding of programming and some basic electrical and mechanical knowledge can...
  20. Replies
    15
    Views
    1,460

    Re: unintended opto output during boot

    TOTALLY AGREE Al, I have had several conversations with the designer/builder about this. Unfortunately he doesn't seem to fully understand the importance of TOTAL control of everything when an...
  21. Replies
    15
    Views
    1,460

    Re: unintended opto output during boot

    Thanks Tom, I wondered if that was the case. Is there a system ready signal that can be used or do I just have an output set to high to drive a relay?
  22. Replies
    15
    Views
    1,460

    unintended opto output during boot

    I am assisting the setup of a lathe that uses a VFD for spindle drive controlled by a KANALOG. During boot there is an output from the JP13 CH 0 that causes the spindle to run. This lasts about 3...
  23. Replies
    2
    Views
    1,068

    >Collet Slipping on .625 carbide drill

    Drilling with live tool on lathe using holder that has ER25 collet. Keep locking the machine up during drilling. Determined the problem is the drill slipping in the collet and overloading the...
  24. Replies
    9,196
    Views
    334,475

    "enlightend buracracy"

    Here in the midwest we have a similar "enlightend buracracy" trying to protect us from ourselves. with the anual spring thaw comes the presence of frost boils on the rural gravel roads, very common...
  25. Replies
    9,196
    Views
    334,475

    Just a little reading to make one wonder about...

    Just a little reading to make one wonder about the true legitimacy of all that is "Global Warming"



    Christopher Pearson | March 22, 2008

    CATASTROPHIC predictions of global warming usually...
  26. Replies
    9,196
    Views
    334,475

    How appropriate, beginning operations on APRIL...

    How appropriate, beginning operations on APRIL FOOL'S DAY.
  27. Replies
    2
    Views
    1,550

    Extra work offsets

    Is this the same for an OM?
  28. Replies
    3
    Views
    1,021

    Thanks for the great help

    Thanks!
    Al's parameter info seems to have worked. Received error 100 until turning off and restarting then had 200 program numbers available. This forum is a great asset to CNC'rs.
    Thanks,
    ...
  29. Replies
    3
    Views
    1,021

    Maxed out number of programs in 0-M

    Is there any way to get around the 63 program max in the 0-M control?
    I have lots of small sub's leaving plenty of memory but need more program numbers.
Results 1 to 29 of 29