Search:

Hello There

I fond this tipic about the cnc controller LNC 510i, and would like to know some questions about it.

does it run with 3D programs?
can i use aspire to make the Gcode?
if so, i...

Hello guys, does anyone know what type of servo motors uses the biesse rover 13 s cnc router?

thanks in advance

Hello guys, does anyone know what type of servo motors uses the biesse rover 13 s cnc router?

thanks in advance

I have a router with two stepper motors on the gantry, it was running ok but suddenly one of the stepper motor reverse it's direction, so they stalled because the gantry became unsquare, i turned it...

Thank you Gerry,

yes i understand now, so in other words both are precise and accurate, as long do not exceed the speed or load, the controller closed loop will fix that right away, while the open...

Hello.

i have a disturbing question about closed loop, and true closed loop system.

looking at the centroidcnc website, they have the acorn, allin, and oak controller borads. i know closed loop...

DOES ANYBODY KNOWS HOW TO RESET A CNC MORBIDELLI MACHINING CENTER, IT LOST ALL PARAMETERS WHEN TIS BATTERY DIES.
IT IS POSSIBLE TO CHANGE THE ENTIRE CONROLLER AND SOFTWARE USING A NEWER RETROFIT...

ALGUIEN SABE COMO PROGRAMAR UN CNC MORBIDELLI 504, DESPUES DE QUE SE LE TERMINO LA BATERIA, NO SE A PODIDO REPROGRAMAR. O BIEN ES POSIBLE CAMBIAR TODO EL CONTROLADOR Y SOFTWARE POR OTRO MAS NUEVO Y...

i am planing to upgrade my cnc machine, i want to replace the regular stepper motors for closed loop stepper motors from Automation technology inc.
my question is, can i still use the same deskcnc...

hello

i am a deskcnc user, few days ago i have experienced an issue, when countoring texts, the steppers lose steps very significative, i have noted that when they are countoring curves on each...

hello

i am a deskcnc user, few days ago i have experienced an issue, when countoring texts, the steppers lose steps very significative, i have noted that when they are countoring curves on each...

since stepper motors have higher torque at low speed and they lose torque at higher speed, reducing the pulleys diameter can give higher speed at the pininon gear with low speed at the motot shaft,...

yes they are in www.novakon.net i want to get two motors to drive the Y axis one on each end of the gantry the steppers are model RS34-2500S it is 2550oz-in,now i need to figure it out what...

one more question, what the wires configuraton would be better? serial, parallel, unipolar,
wich one can give more torque or speed, because impedance is different betwen each configuration, power...

ok i understand, thank you very much for your help, maybe later i will have lot of more questions about the machine since i want to upgrade it to make it better. have a great day.

can you explain me how did you do the calculation for the max voltage rating of the motor?

i don't know exactly how to read the v.a of the steppers for example, the one 640 oz-in
is V 4.05, A 4.5 , MH 6.8, how to calculate the max power supply voltage?
the pinion is 1-5/32" overall...

My machine is 48 x 96 cutting area, it is rack and pinion driven with belt and pulley geared on the Y and X axes, Z axis is screw driven, it runs ok at 130 inches per minute in cutting and about 250...

yes it does, go to www.homeshopcnc.com they say gecko drives can run any of the models they have including the large 2550oz-in stepper shown in their stock.

increasing the torque of the stepper motors can they run faster without missing steps? i need speed up my cnc router, i have 1200 oz on the Y, 640 on the X and 264 oz on Z, i am planing to change the...

you need a ASD36B-K (Driver) from oriental motor, go to www.orientalmotor.com and type the vexta motor number you have on the part number search, it will display the motor and the drive, price and...

i know shopbot cnc uses vexta alphastep closed loop stepper motors, does anybody know what part number they are? what type of gearboxes they are attached to? i want to upgrade my cnc machine using...

hola usuarios de routers cnc.

estoy tratando de diseñar un sistema de succion para mi router, se que no hay nada mejor que una bomba de vacio de alto poder pero devido a lo costosas que son no me...

hi all, im trying to find out how to design a hold down vacuum system for my
4'x8' cnc router, i have a leybold trivac D16A vacuum pump, but don't know if it will be able to pull the material...

hola amigo, bienvenido al mundo cnc, si tienes pensado construir un router cnc
yo puedo darte algunas recomendaciones acerca de las partes necesarias,ya que yo construi el mio y me a funcionado muy...

gracias por tu sugerencia.
ahora mi pregunta es puedo usar los stepper drives gecko 201 con un software mach?
el sofware mach viene con un control board o de donde conecto los stepper drives?
si...

gracias por tu sugerencia.
ahora mi pregunta es puedo usar los stepper drives gecko 201 con un software mach?
el sofware mach viene con un control board o de donde conecto los stepper drives?
si...

hi,xichanceix
have you checked out the machine velocities in the deskcnc software?make sure that's in a correct settings, and also see what number you have entered in the "contouring" parameters,...

hi all cnc users.
i've built a cnc router,using stepper motors and Deskcnc software.
now my idea is to design a sharpener machine using the cnc technology,specially designed to sharp spiral cutter...

hola usuarios de cnc.
he construido un router cnc con motores steppers y controlador deskcnc y hasta el momento a estado trabajando bien, ahora tengo en mente construir una maquina para afilar los...