584,863 active members*
4,938 visitors online*
Register for free
Login

Search:

Type: Posts; User: coop31

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    711

    Re: tool changer drifting back

    figured it out...Linear tracking tool drum was selected.
  2. Replies
    1
    Views
    711

    tool changer drifting back

    Hey guys,

    My tool changer on my older Arrow 750 with a2100 control is acting up. The air cylinder pushes the tool changer to the spindle, but as soon as it gets there the air pressure is shut off...
  3. Re: Timer for startup and stop off workstation Acramatic 2100 Arrow 750 97'

    Hey, I had a very similar problem a few weeks ago.
    Machine was running perfectly fine, then all of a sudden I heard the spindle stop. I looked over and the computer was shutting down, When I tried...
  4. Re: Timer for startup and stop off workstation Acramatic 2100 Arrow 750 97'

    I had a similar issue. I resolved it by bypassing the timer, Attach these 2 black wire together.

    473242.
  5. Replies
    8
    Views
    1,892

    Re: Increase memory - Acramatic A2100

    A couple of my arrows have like no program storage...option was not purchased so i think its like 150k of program storage.

    It's not a problem though because you don't need it if you can figure out...
  6. Replies
    20
    Views
    10,285

    Re: Acramatic 2100 Alarm 44-84

    Sent to your email. Let me know if you got it.
  7. Replies
    20
    Views
    10,285

    Re: Acramatic 2100 Alarm 44-84

    PM me your email address and I'll send you the pdf
  8. Replies
    2
    Views
    961

    Re: Complete A2100 available

    I would love to have some spare boards.

    if you can ship it to canada I'll cover the shipping cost.
  9. Thread: Need RT Bios

    by coop31
    Replies
    1
    Views
    701

    Need RT Bios

    Can anyone help me out with the bios settings for real time board 3-424-2171A01

    I've got all the equipment needed to do this.
  10. Re: Arrow 750 Acramatic A2100 - All the gear, no idea

    does your machine have a network adapter installed? much easier that way.
  11. Thread: Arrow 2 EKK

    by coop31
    Replies
    14
    Views
    1,555

    Re: Arrow 2 EKK

    I would also say phase issue. I had the same problem. Spindle running correct is not dependent on phase.
  12. Replies
    3
    Views
    2,000

    Re: A2100 CONTROL HELP

    As Mav said, you might run into problems with the hard drive turning on a off. I would disconnect the hard drive to eliminate any chance of corrupting it.
  13. Replies
    5
    Views
    1,200

    Re: Cincinnati Arrow 2 500 EKK CNC VMC

    i Have a 1250c with simodrive 611. My machine is 400 volt.
  14. Replies
    0
    Views
    3,461

    Trying to edit a post that Ive downloaded.

    Hey guys...

    I'm trying to edit a post that Ive downloaded and I don't really have a clue.

    Its outputting inverse time feed rates and that's fine, but my machine doesn't like the numbers it...
  15. Replies
    6
    Views
    1,651

    when did bobcad get so expensive

    I purchased 3 seats of version 26 mill3x pro for like $1000

    Called and asked about the new version with 4 axis and was told it was $6400 for one seat. Is that crazy or perfectly normal?
  16. Replies
    1
    Views
    646

    lost my cam tree...

    playing with the demo and i closed my cam tree. How do you get it back?
  17. Replies
    6
    Views
    1,024

    Re: 4th axis question...

    Thanks for the help today Greg!
  18. Replies
    6
    Views
    1,024

    Re: 4th axis question...

    I have a2100 control with 4th axis ready from factory. I bought a Cincinnati Milacron Sabre labeled NC-10-B 4th axis. It hooked right up to the machine with no alterations.

    4th axis seems to...
  19. Replies
    6
    Views
    1,024

    4th axis question...

    Can anyone confirm that their 4th axis can do full 4 axis simultaneous machining. Mine does not. seems it will only position,then 3 axis.
  20. Re: Have to open and close door to run next program.

    More..System Config..Machine Application..Cycle Control... uncheck "MAI End Of Program Enable"
  21. Re: Have to open and close door to run next program.

    You didn't dig quite deep enough...Lol
  22. Re: Have to open and close door to run next program.

    SUCCESS...

    There is a setting that needed to be changed...
  23. Re: Have to open and close door to run next program.

    Very Interesting Maver1ck.. I assumed it had something to do with the software as my other machines don't do this.
  24. Replies
    11
    Views
    3,201

    Re: Drives not enabled

    PROBLEM SOLVED...

    Thank you so much for leading me down the right path to finding the problem. I have no idea how this happened, but one of the wires on the e stop came loose. What a relief. I was...
  25. Re: Have to open and close door to run next program.

    I don't think I have the optional M codes.

    Might be easier to pop a hard drive from another machine in there or is it part of the MAI?
  26. Replies
    11
    Views
    3,201

    Re: Drives not enabled

    Thanks for the info Mav. Sorry for taking so long to respond... Since this post I have moved everything into a proper shop and it has taken some time.

    I have messed with this machine again in the...
  27. Re: Have to open and close door to run next program.

    Well that sucks...lol
  28. Replies
    5
    Views
    2,368

    Re: Arrow 2 axis motor coupler...

    Found a suitable replacement. " Lovejoy GS 24 Spider 98A Red"
  29. Have to open and close door to run next program.

    Hey guys... On my newest arrow 750 (A2100) I have to open and close the door after a program runs in order to run the next program. It's driving me crazy... It's my only arrow (I have 5 now) that...
  30. Replies
    5
    Views
    2,368

    I called Lissa in Canada a week ago and still no...

    I called Lissa in Canada a week ago and still no answer. Someone at your place called me and was looking into it for me yesterday. Hoping to hear back soon.
Results 1 to 30 of 204
Page 1 of 7 1 2 3 4