May be FX702 if at all inside the Nc rack is the culprit as in one of our Mazak when the screen was shacking and getting frequently hanged we got it repaired and solved the problem.
Chandru
Type: Posts; User: CHANDRU
May be FX702 if at all inside the Nc rack is the culprit as in one of our Mazak when the screen was shacking and getting frequently hanged we got it repaired and solved the problem.
Chandru
DEAR FRIEND,
PL CHECK THE CRT CONTROL UNIT AND IT WILL BE HAVING THE FOLLOWING CARDS
FX32B
FX42A
FX52A
FX62B
There will be one led in the FX52 CARD AND IT WILL BE BLINKING IF THE DATA...
DEAR JL,
THANKS,
OUR PROBLEM IS WHEN WE SWITCH ON THE M/C THE DRIVE IS GETTING ON OK FOR SOME TIME AND AFTER WORDS IT IS GOING BACK TO 55 ALARM STATE.
THE RED LED WHAT YOU HAVE MENTIONED...
DEAR FRIENDS,
WE HAVE ONE MAZAK 35-60 WITH MRS SINGLE AXIS DRIVE FOR X,Y&Z AXIS.
WHEN EVER WE SWITCH ON THE MACHINE WE ARE GETTING EMERGENCY STOP ALARM AND THE FAULT INDICATION IN THE RF701...
DEAR MACTEC,
THANKS FOR SUCH A WONDERFUL HELP.
I AM IN NEED OF SOME MORE HELP.
THERE ARE TWO ADJUSTING SCREWS ONE ON THE TOP AND THE OTHER IN THE SIDE.
WHAT ARE THEY AND HOW TO ADJUST...
DEAR FRIENDS,
WE ARE HAVING A PRESSURE PROBLEM IN ONE OF OUR VANE PUMP AND IT IS QUITE OLD.
WHEN WE CHECKED THE PUMP THERE ARE 2 O-RINGS WHICH ARE WORN OUT COMPLETELY AND WHICH ARE MOUNTED IN...
DEAR AL_THE_MAN,
THANKS FOR YOUR TIMELY AND WONDERFUL HELP.
CHANDRU
DEAR FRIENDS,
WILL ANYBODY PL HELP WITH THE SIGNALS/WIRING DETAILS OF THE HEIDENHAIN ENCODER ROD 271.
THANKS
CHANDRU
Friends,
Are the keys in the key pads/push buttons in the fanuc o series controller are membrane switches.
Sorry if I am wrong.
Can we replace them with new membrane switches and can...
Friends,
We have one MAZAK ST40N with FR-SE spindle drive.
The drive has come back after repair and we are suspecting the settings of these switches.
Will any body pl help with the SW...
FRIENDS,
WE REQUIRE THE PIN/SIGNAL DETAILS FOR THE PORT CNB IN THE ORIENTATION BOARD A20B-0008-0240.
CAN ANY BODY HELP.
THANKS,
CHANDRU
Friends,
We have one MAZAK-ST28 with CAM T3 controller.
In the machine parameters page no 4 we are having K-PARAMETERS.
Will any body pl explain what are these parameters as we donot have...
THANKS JOHN EAGERLY WAITING FOR YOUR HELP.
CHANDRU
THANKS FOR BOTH ROKINS AND ONTHEBUMPER,
THE FAULT WAS WITH THE ENCODER CABLE.
CHANDRU
FRIENDS,
IN ONE OF OUR CINCINATTI 2100 MACHINE WHEN WE SWITCH ON DURING THE BOOTING PROCESS WE ARE GETTING THE ALARM e0007 one of the driver is missing. LOOKS LIKE THE PENDANT IS NOT RECOGNISED...
FRIENDS,
WE HAVE A VMC WITH MITSUBISHI 520 AMR CONTROLLER.
EVERY DAY IN THE MORNING WHEN WE WANT TO HOME RETURN THE AXES WE ARE GETTING SERVO ALARM IN THE Z- AXIS( WHEN WE CHECKED IN THE DIAG...
FRIENDS,
ANY BODY PL HELP ME AS HOW TO ENTER /CONVERT THE MTY PARAMETER OF MRS-10 DRIVE.
THE MOTOR MODEL IS HA100 AND THE CORRESPONDING MTT VALUE IS 2
THE DETECTOR IS 5000P/R ENCODER...
Dear Larry(MTSS),
Thanks for your reply but the problem is in the programme file we have stored only one programme and this alarm comes when we want to create a new programme.
Thanks,
...
Friends,
When we want to create a new programme(mazatrol) we are getting the alarm no 404 blocks>500.
But when we check the programme file screen we are are getting blocks used 27/500.
A...
Dear decoupar,
The machine is an INDIAN MAKE and the controller is FANUC 0i-TC
Thanks,
CHANDRU
Dear dcoupar,
The cycle works fine with components having dia of less than 100mm but when the dia increases above 100mm this problem is occuring.
Should we go for G92 instead of G78
We...
Thanks dcoupar,
The machine is nothaving a gear box.
CHANDRU
Dear dcoupar,
The spinle is stalling after few passes and that too while doing initial setting.Suppose we are not getting the proper thread form after the completion of the cycle and when we give...
Dear decoupar,
YOU ARE WRIGHT AND THE PARAMETER 3401 BIT 6 IS 1.
COULD YOU PL TELL ME WHERE EXACTLY WE HAVE TO INSERT THE G95 CODE.
THANKS,
CHANDRU
Friends,
Recently after commissioning a cnc with oi-TC controller we had G78 Threading cycle problem.
While machining after few passes the spindle was stopping and the tips were breaking.Later...
Friends ,
Many thanks for everyone.
The actual problem was the original encoder was BALUFF and the replaced one is PEPPEL.
The wire color coding of the R and R-ve Signals there was some...
DERA FRIENDS,
IN ONE OF OUR MACHINE WITH FANUC oi TC CONTROLLER WE ARE GETTING ALARM AL27 (9027)
THE POSITION CODER OF THE SPINDLE MOTOR IS CONNECTED TO JYA2& THE ENCODER IS CONNECTED TO...
Friends,
What precautions/folowups required while changing the main circuit board for a ac digital spindle drive.
The spare board is having different version no.
Thanks and Regards,
...
Hellow friends,
we do have one miayano bnc 34t with lns hydrobar feeder of finger type.
Any body please help as how to progrm using the bar feeder like m-codes and g-codes with a sample...
HELLOW FRIENDS,
WE DO HAVE ONE MIAYANO BNC 34T WITH LNS HYDROBAR FEEDER OF FINGER TYPE.
ANY BODY PLEASE HELP AS HOW TO PROGRM USING THE BAR FEEDER LIKE M-CODES AND G-CODES WITH A SAMPLE...