Nice work, thanks for sharing.
Type: Posts; User: WeCheat
Nice work, thanks for sharing.
My vote is opti-mic :cool: would be nice if you could re post the pics and maybe a video.
Greg
Thanks that is what I needed. :banana: You are great!
Ok I am not getting anywhere looking at inverters for my truck. What I don’t know is how much I need from the truck. For example I have 14vdc making 70amp I get 980 watts right? They say most...
Welcome to the site!! I had a setup like you are talking about a few years back. It used a 8in metal saw (looked like a 7 ½ circular saw) but it has a clutch setup in it so if the blade gets stuck it...
Sweet just sweet. Nice work and thanks for sharing.
Greg
Nice Site, Should help a lot of people out. Thanks for spending the time to share.
Greg
Sweat :rainfro: Like dude tell us a little more on your project. Good, Bad, PITA, what sent you for a loop AND what did you build it for? :rainfro: Sorry I am in 60's flash back right now...
Thanks That will get me started.:cheers:
Need some information on this driver. Have emailed General Controls but have not received a reply back from them. Anybody got a manual for this drive? Model: 29A55-A 3amps input: 28vac/42vdc ...
I watched all ten of your videos and thought they’re great especially for beginners trying to get their feet wet. The only thing that I think you should change is when you were working with your...
NC Cams Is right bathroom scales work really well. I have been set for over fifteen years. They will get you too within 1% if you’re careful and do your setup exactly the same. I’ve checked the...
Sweat little project you got there. real nice and welcome to CNC Zone:cheers:
When I had my tig machine and converted it to water cool I used small parts water from harbor freight. It held about two gallons and a small transmission cooler that was bolted to the back of...
Here is the Powermax 1000 service manual to down load http://www.wecheat.com/cnc/1.htm see if this helps.
Go to the paintball store and get a co2 tank and reg cost about $3.00 to 5.00 to fill a 20oz tank.
Cool Thanks:)
I am looking for some I.C magazines so I can learn a little before I dive in. I found this site http://www.modelenginebuilder.com/
Is this a good one and are there any you all can recommend?...
Here’s a list of rod that we used to repair GM frames and have seen no problems. I have repaired a lot of frames on pickups due to the fact Oilfield people love to overload and drive fast down dirt...
I own the Pro version and it is an excellent program even though it is a pain to set up. Documentation is much easier to do in this software then in my previous ones I have used. I have been happy...
Try these two link for stepper and Welcome to the site
http://www.geckodrive.com/photos/Step_motor_basics.pdf
http://www.pminmo.com/drivers.htm
I had a service/repaire manual sent to me from a rep see if this is what you need
Sevice manual for a 1000
Take a look here I put them on my site Hypertherm 900
If you need more let me know and I will try to get it
The photos I sent you were not what you were looking for? If not please are more specific and I will see what I can do.
Greg
I own a hypertherm 900 and did not have a wiring diagram so I just unscrewed the torch at the machine and just ohm the wires while pushing the switch to find the right two wires. I was never able to...
I have geckos, Bob Campbell board and THC unit 6amp 50v motors (I think :-) I do not have the motors here with me.) A computer nerd told me I need to build a parallel port emulator?? Or emulate a...
All I can say guys is the response is pretty awesome to my question and I really appreciate it. Let me clarify what I want to know and why I want it.
1: a stepper controller that requires no PC or...
Just one to test with. A small power supply, so all I have to do is plug it in the wall and start working the motor. I just want to keep away from having everything scattered on a work bench...
you lost me after " I have seen several people " I was looking at this http://www.cnczone.com/forums/showthread.php?t=14095 and thinking if no one made Standalone Control I could use it (real cheep...
I was wondering if any one made a standalone controller for stepper motors. Basically what I’m looking for is something that I do not have to hook up my computer during the construction phase of my...