508,286 active members
3,196 visitors online
Register for free
Login

Search:

Type: Posts; User: ynneb

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    34
    Views
    3,549

    Re: Aussie Plasma Build

    Your build looks great Will. I'll be following its progress from now on. Keep up the great work.
  2. Re: Designing ISO20 spindle w/ tapered roller bearings and ball bearing stud puller.

    Ha ha, its been years since I have posted in this forum and many months since I have visited it, yet the very first post I have looked at, this one, seems to need moderation. (Despair ;) )
    I see...
  3. Replies
    125
    Views
    6,188

    Looks good!!! From memory, I was thinking that...

    Looks good!!!
    From memory, I was thinking that the steering wheel platform was to pivit forward, to enable easier in and out.
    I'm not sure what you should do for spacers that join the bottom and...
  4. Replies
    125
    Views
    6,188

    Ha, I cant believe someone has revived this...

    Ha, I cant believe someone has revived this thread.
    Good luck buddy, I'll be interested in how you go. Triple check everything before you cut.
    Please post a pic of the result even if it goes...
  5. Replies
    4,472
    Views
    409,856

    It's been a while since I looked back on this...

    It's been a while since I looked back on this thread, and the recent discussion is interesting. As a moderator and also the starter of this monstrous thread, here are a few my thoughts. (Not rules,...
  6. Sticky: Gary, I just carried out the two experiments and...

    Gary, I just carried out the two experiments and setting from your last two posts.
    I think I will try to find another printer cable. Yes you are correct that it does not have USB.
    I notice when the...
  7. Sticky: Hi Gary, I did the tests as directed and have...

    Hi Gary, I did the tests as directed and have even taken screen captures.
    No show again.

    I think I'll do some hunting to see how to wind back the firmware.

    Damn Gravograph and their propriety...
  8. Sticky: Thanks for the suggestions Gary. Still no go. I...

    Thanks for the suggestions Gary.
    Still no go. I turned everything off and still got the error.
    I set up the page size in Inkscape, keeping in mind I get the error with just jogging, so I dont think...
  9. Replies
    4,472
    Views
    409,856

    Hi all, is this thread still going? wow !! Can I...

    Hi all, is this thread still going? wow !!
    Can I please remind all to post in English only.
    I had to delete a few non English posts today.

    Keep going !!!
  10. Sticky: Hi Gary, thanks for your responce. A friend of...

    Hi Gary, thanks for your responce.
    A friend of mine bought the machine at an auction for 35 bucks :)
    It didn't come with any software and the Gravograph website offers no appropriate downloads....
  11. Sticky: Hi Gary, I installed it today. Very impressive. I...

    Hi Gary, I installed it today. Very impressive. I envy guys like you, with such talent.
    I am having troubles with getting a Gravograph IS 200 to work.
    I am sending the signal as HPGL. The...
  12. Replies
    6
    Views
    1,229

    Woah !!! That's brilliant !!! I can tell you're...

    Woah !!! That's brilliant !!!
    I can tell you're going to be a great member of CNCZone.
    Welcome to the forum.
  13. Replies
    6
    Views
    1,229

    Hi Ron, No I did not make these, but shamelessly...

    Hi Ron, No I did not make these, but shamelessly borrowed them to demonstrate what I was talking about.

    The project I am contemplating is a steampunk grandfather clock. In the lower part of the...
  14. Replies
    6
    Views
    1,229

    The Steampunk thread.

    Please post pictures, details, and input concerning steampunk creations into this thread.
    What have you made? How did you go about it. What are your thoughts about this genre?
    ...
  15. Replies
    4,472
    Views
    409,856

    All posts MUST be made in English. All non...

    All posts MUST be made in English.
    All non English posts will be removed.
    You may however post in English first and then put a non English translation below, providing they are in the same post.
  16. Ive done some further testing and its looking...

    Ive done some further testing and its looking promising.
    I have attached the working file for a .6 x 3.6 board.
    The picture you see below is a small section of one sheet.
  17. Using a program like GIMP or Photoshop. You could...

    Using a program like GIMP or Photoshop. You could then use the paint brush in spray mode.
    Export it out and then into Inkscape and convert the raster into a vector drawing. From that point on...
  18. Replies
    4,472
    Views
    409,856

    Try SheetCam...

    Try SheetCam it is very cheap but is great for 2.5D work. Test their trial version.

    OR

    CamBam Another Great CAM program
  19. Replies
    4,472
    Views
    409,856

    Fleury, there seems to be lots of posts about...

    Fleury, there seems to be lots of posts about uploaded files been password protected.
    What is the reasoning behind this? Are you able to remove the password protection or post the pass word in this...
  20. Replies
    4,472
    Views
    409,856

    Thanks again Exsecratio / Dave for a fascinating...

    Thanks again Exsecratio / Dave for a fascinating insight, into the world of laser cutting.
    As much as I hate the MDF dust and having to replace / sharpen router bits, I can now see that laser is not...
  21. Replies
    4,472
    Views
    409,856

    Thanks Exsecratio for taking the time to explain...

    Thanks Exsecratio for taking the time to explain about the lasers. Do you know why the cost is so high for re-gassing?
  22. Replies
    4,472
    Views
    409,856

    Thanks Fleury for taking the time to do that. Is...

    Thanks Fleury for taking the time to do that. Is the glass cover to stop the smoke?
    It seems like a small laser module. How many watts? What type of Laser? Are there any consumable parts involved?...
  23. Replies
    4,472
    Views
    409,856

    I'm interested to see how the laser looks when...

    I'm interested to see how the laser looks when cutting. Maybe a video is good.
  24. Replies
    4,472
    Views
    409,856

    Fleury, are you now using a laser? What type, and...

    Fleury, are you now using a laser? What type, and how much did it cost. Can we see a pic of the laser in action.
    Good work.
    Benny
  25. Replies
    125
    Views
    6,188

    Did anyone ever make one of these?

    Did anyone ever make one of these?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4