584,849 active members*
3,854 visitors online*
Register for free
Login

Search:

Type: Posts; User: kevins75

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,176

    if you have a paper copy of the parameters why...

    if you have a paper copy of the parameters why not just hand type them and be done with it?
  2. Replies
    3
    Views
    1,335

    your dc control codes are probably not set right,...

    your dc control codes are probably not set right, test by searching up program and turning on single block. hit cycle start and then computer should just sit there waiting for you to run program, if...
  3. Replies
    12
    Views
    4,942

    the pe1 led stands for parity error, if the dip...

    the pe1 led stands for parity error, if the dip switch 2 procedure does not clear this, did you check the battery on the board? this is the fx84 in the lower card cage? does the ready light come on?...
  4. Replies
    3
    Views
    847

    those are checksum values, you do not need to...

    those are checksum values, you do not need to enter them.
  5. Replies
    5
    Views
    1,364

    what alarm codes are you getting?

    what alarm codes are you getting?
  6. Replies
    2
    Views
    1,668

    go to diagnostics then wh and set address 66EB9...

    go to diagnostics then wh and set address 66EB9 and set the data value to 00
  7. Replies
    75
    Views
    15,640

    maybe this will help you out with the transistor...

    maybe this will help you out with the transistor checks
  8. Thread: Meldas 310

    by kevins75
    Replies
    4
    Views
    2,202

    if you look on the back of the machine you will...

    if you look on the back of the machine you will see a metal plate with the machine builders name on it, what is that name?
  9. Replies
    75
    Views
    15,640

    make sure to check your base transistors before...

    make sure to check your base transistors before powering up or you will have a fireworks show.


    ps those resistors on the right hand side of the board do get hot so may be discolored and still be...
  10. Replies
    7
    Views
    790

    kentucky rebuilders?

    kentucky rebuilders?
  11. Replies
    12
    Views
    3,252

    try tapping on the top of the caa card and watch...

    try tapping on the top of the caa card and watch the 7 segment display to see if it flickers between different conditions.
  12. Replies
    25
    Views
    9,253

    when the machine is booting up ot looks for the...

    when the machine is booting up ot looks for the system floppy disk in the control, if the disk is bad or not in the drive you get a fld loading error.
    check to see if system disk is in drive, if it...
  13. Replies
    15
    Views
    1,645

    try these settings and see if you get better...

    try these settings and see if you get better results on output.
    OP1 109
    OP2 8
    OP3 109
    OP4 70
    OP15 1
    OP16 206
    OP17 100
    OP18 100
    OP20 100
  14. Replies
    15
    Views
    1,645

    if you try to output a program from the machine...

    if you try to output a program from the machine to the computer does it act like it is sending out ok or does it throw up an error right away?
    does your computer get anything? garbage characters,...
  15. Replies
    15
    Views
    1,645

    you have all the hardware you need with the fx17,...

    you have all the hardware you need with the fx17, you should have 2 rs232 ports on the machine, one for the cmt and one for the tape. it looks like you just need to set up your parameters.
    can you...
  16. Replies
    15
    Views
    1,645

    what are the boards you have in your control? if...

    what are the boards you have in your control?
    if you go to diagnosis screen and take a look in the lower center portion you will see your software versions come up, what are they?
  17. Replies
    6
    Views
    1,029

    hows this?

    hows this?
  18. Replies
    6
    Views
    1,029

    what is machine model and control type?

    what is machine model and control type?
  19. Replies
    13
    Views
    5,527

    check your spindle drive and see if any lights...

    check your spindle drive and see if any lights are on it or is it dead?
  20. make sure parameter 9005 is set the same as 9001...

    make sure parameter 9005 is set the same as 9001 and 9006 is set the same as 9002 then try it again.
  21. Replies
    21
    Views
    3,688

    I am trying to remember, does the tool need to be...

    I am trying to remember, does the tool need to be zeroed out maybe?
  22. Replies
    21
    Views
    3,688

    did you zero return the machine first?

    did you zero return the machine first?
  23. most people never had that data, just set the...

    most people never had that data, just set the travels to 99. and -99.
    the rest of the screen would be set up so you could not crash your machine so you would set it up for the size of the chuck.
  24. Replies
    21
    Views
    3,688

    s100 m03 and see what happens.

    s100
    m03
    and see what happens.
  25. Replies
    21
    Views
    3,688

    i think the comments in brackets are what is...

    i think the comments in brackets are what is confusing it, take those out and just try some basic g commands to see what happens.
  26. the p32 means an unknown code is being sent,...

    the p32 means an unknown code is being sent, maybe just try going to tape mode and pressing cycle start and see what happens.
  27. Replies
    12
    Views
    3,252

    did you check the parameters on the drive to see...

    did you check the parameters on the drive to see if scrambled?
  28. Replies
    12
    Views
    3,252

    hopefully right file

    hopefully right file
  29. Replies
    12
    Views
    3,252

    here is a diagram of the board, the eproms and...

    here is a diagram of the board, the eproms and eeprom are the chips that need to be swapped.
  30. Replies
    12
    Views
    3,252

    alarm 12 is a memory error on the sf-ca card....

    alarm 12 is a memory error on the sf-ca card.
    you just need to swap the card itself, make sure to change the software chips,the eeprom chip and set the jumpers the same way as the original card and...
Results 1 to 30 of 47
Page 1 of 2 1 2