thanks for the wiper info
Type: Posts; User: garychipmaker
thanks for the wiper info
Thanks I found the bolts buried in sticky coolant and chips. bolts were where you said. Others had said bolts were other places Now I have to figure out what are the proper way cover wipers and...
I cant figure out how to get the wires out off the terminal block of the input voltage transformer. There are no visible screws . I need to change to voltage jumper wires for my higher voltage which...
Where can I get a Sd1525-10 servo drive module I called Servo Dynamics they said it would be 6-8 weeks lead time for a repair
This is in a tree 310 Is a cavity mill event an option. I noticed it in the manual but I can't find it in the control. It isn't something I need to use. I would like to dripfeed from a PC in the...
You could run that in conversational event type 4 circle mill with about 30 seconds of programming
Hi is there a way to program the alphabet & numbers using a dynapath delta 20 I don't have it running off a pc thanks
Hi How do you tap with a Dynapath delta 20 control on my Tree 310 mill. I have the manual but I think it needs something more in my control. book say you can use a floating tapholder but my spindle...
Hi I ran this program for step and repeat just to check it would work . It's the same as the program you posted from the manual I just downsized the program because my Y axis doesn't have have that...
I'm glad I'm not the only one that has had this problem. My manuals show that the steps have to be incremental.
I need a wrench for a Tree 310 mill spindle nut. I has a #30 mntb quickchange spindle I haven't found any information on what size the wrench is or where do i buy one. And yes I can make one I just...
I need a wrench for a Tree 310 mill spindle nut. I has a #30 spindle I haven't found any information on what size the wrench is or where do i buy one. Thanks
Thanks Its one of those things that are so simple after you know how it works I was trying to take it apart and never did figure what holds the nut from coming off after you take out the screws
Hi I can't figure out how to get the spindle nut apart on a # 30 quickchange spindle. The nut hits a stop before it is tight on the toolholder. I remove the 3 screws but how does it come apart is...
I sent my servo dynamics drive control to Parts and Smarts. Al tuned it but I still have the .0156" axis lag at standstill. I talked to Al and he thinks there may be a ground issue. I tried adjusting...
Hi I'm not getting an * after a program line so it isn't in position delta 20 with servo dynamic drive control Baldor servos. I'm not having much luck getting the drives adjusted I know how to get...
Hi I'm not getting an * after a program line so it isn't in position delta 20 with servo dynamic drive control Baldor servos. I'm not having much luck getting the drives adjusted I know how to get...
Hi I'm not getting an * after a program line so it isn't in position delta 20 with servo dynamic drive control Baldor servos. I'm not having much luck getting the drives adjusted I know how to get...
Hi I'm not getting an * after a program line so it isn't in position delta 20 with servo dynamic drive control Baldor servos. I'm not having much luck getting the drives adjusted I know how to get...
I sent my delta 20 control to Parts and Smarts. I got a call back with bad news power supply was bad. Processor was blown and blew out their processor and aux board had problems They said it may be...
Hi my 3 phase has a wild leg My incoming power to the first cabinet has 123v on two legs and 217 on the wild to neutral. The mill did work for a couple months then developed this problem. I may have...
My TREE 310 with delta 20 control has no power to the servo dynamics drive or the spindle motor or knee lift motors will run if contact is manually pushed in other cabinet.I can't figure out the...
My TREE 310 with delta 20 control has no power to the servo dynamics drive or the spindle motor or knee lift motors will run if contact is manually pushed in other cabinet.I can't figure out the...
Hi I've been on here before asking questions about this mill TREE 310 dynapath 20. After searching old posts for info I'm wondering if the incoming power is connected correctly. Does anyone know...
Hi I'm in east central Iowa
Okay middle position has 217v left and right have 123v. what I have found is the cabinet with the dynapath controls has 3 fuses in the upper right corner. The left fuse has 0 v middle 217v right...
Hi I've been on here before asking questions about this mill TREE 310 dynapath 20. After searching old posts for info I'm wondering if the incoming power is connected correctly. Does anyone know...