Search:

This is 1400-2 cpu; After WANT TO GO TO THE LAST HOME; yes; shows NUMBER OUT OF RANGE, next shows TOO.3.0000, tool table is ok; T1 .500/-1.00.
Thanks for help.

the blue ribbon wire at bottom of x controller card and the one out side the junction box

Reinitialize the memory type RI (enter)answer the QS ( first back up machine parameters (setp) your programs, tools and fixture offsets.) if that won't work, clear the memory by typing DI (enter) G0...

When swapped the axis amps; did u swapped the White and Brown wires at the bottom?

Check backlash, look for loose motor coupler. Turn of machine, reach for the z ballscrew, by hand turn it back and forth, the head should move; if does not move or is too lose, the nut attached to...

points to check: air pressure 120psi; draw bar broken bellvilles springs (washers) Draw bar assy has a halleffect switch inside (piston); on top pulley there is a magnet (0.06 clearence within them)....

hose coming into reservoir should be warm, hose out chiller unit cold; pump should be on all the time; chiller with a thermostat on and off.

All is needed is a 14" new or used LCD monitor
Analog to VGA video box converter
15 pin short Vga cable
Rca male connector
2 outlets electrical strip

For installations instructions Email me...

Perform a 45 degree test and adjust the clock card.

perform a 45 degree test and adjust the clock card.

01*MAIN PROGRAM
G0G90S1200M3X0Y0E1
1)0M98P2L1
2)M98P3L1
3)M98P4L1
4)M2
line 1 calls prog #1 once
line 2 calls prog #2 once
so and so.
At the end of each sub program instead of M2, insert M99...

Use fixture offsets

check power supply for +/-5 &12 vdc. some times keyboard keyes are stock.

look inside back cabinet for a black relay with a white bootm in the center if sticking out. push it back in

look at the serial # ' that tells the date it was build

Download the program to the pc, delete all N# and upload it back (with no N#) the type NU

.

try this: save all the programs, parameters and backlash,fixture and tool tables; at the enter nex command type : G0 (enter) G0 3000 (ENTER) go to second screen and hit #5 a couple times (if you...

.

Easy and quick way to aligne the turret : load one holder at bucket #1 and #11, get an indicator on a high gauge and jog it under the turret at #1 tool holder bottom flange and set to zero; jog the...

ad more mem to the machine!

Make shure parameter is set for 7500 rpms.!and the belt is tight!

that was what I spent on replacing my 1985 vmc 40 $350.00 used ctr.
Anyone wants to do that; email me at [email protected]; be glad to tell you how (soooo easy)

The cnc is not going to read from the hdd; the 32mp pc, works exacly as your desk top pc using the rs232 port.

remove all the bolts holding the cover to the saddle, pull it and thre is 4 bolts at the base

Remove the pump (gold assy) some times the bearing gets a lot of rust overloading the motor; also remove the big nut (2 of them)and clean the screen inside.

HI EVERYONE! I am looking for a working used Toshiba ESP 130, 230 volts for my 85 vmc 40.. I will appreciate any info. My fried beyond repair.

You can replace as many as u want! If is the Blue AirMc assy outside machine, yo need to remove the 2 black srcrews and cut the 2 black wires (if no conectors); same with small ones mounted on a...

M98P#/ M99

make shure Spindle controler card is the right one with the AC eprom (xyz cards are the same as this one); -4-5 sys spindle card has a soldered jumper A+B (not shure) Also check relays back cabinet!