584,846 active members*
3,811 visitors online*
Register for free
Login

Search:

Type: Posts; User: regocolm

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    612

    VF9 Y Axis Problems

    Hi Guys,
    Have a problem with the y axis encoder on my haas vf9-40. Machine is 2013/14,
    The problem occurs when i go to move the y axis after referencing the machine.
    I get to move the y axis...
  2. Thread: Mv1200s

    by regocolm
    Replies
    1
    Views
    2,179

    Re: Mv1200s

    May be able to look at the problem if you give more information. What material are you trying to cut? Are you flushing nozzles close to the part?
    You can copy E value conditions and change specific...
  3. Thread: BMC40 Parts

    by regocolm
    Replies
    0
    Views
    496

    BMC40 Parts

    Hi Guys,
    Have a major problem with our bmc40 ultramax,
    Long story short,operator didnt set z value,
    cycle start, catastrophic crash. The z-axis lead screw is damaged and housing.
    Question...
  4. Replies
    1
    Views
    931

    Toolset Problems

    Hi Guys,
    Recently acquired a brilliant vm20 centurion 7, it came with a renishaw probe omp40-2 and ts27r wireless toolsetter.
    ran the toolsetter when we first started using it and it worked fine,...
  5. Replies
    1
    Views
    9,130

    Re: post processor

    yes, post processors are compatible, just go to the onecnc folder - settings and copy all your post processors into the same folder in xr7. Hope this helps
  6. Replies
    14
    Views
    6,516

    Re: OneCNC XR7 for sale

    Hey Haasman,
    What version of XR7 is it?
  7. Re: Eletrox scorpion fibre laser + maxbox Engraving/marking laser for sale

    Hi emlclcy,
    Is it a big job to remove the laser from the housing and use it for marking larger parts?
    Also what is the max marking area in one shot? eg 100 X 100 / 200 X 200
    ...
  8. Replies
    10
    Views
    4,697

    Re: Hurco BMC40 Hard Drive Replace

    Yeah i was surprised to hear that, was talking to andy bennett in hurco uk, If there's anything you can do to help us out at all, We do not require a warranty with this service, We just want to get...
  9. Replies
    10
    Views
    4,697

    Re: Hurco BMC40 Hard Drive Replace

    Thanks Bloke for the quick reply, have been talking to hurco and they say that they do not support that service of creating a new hard drive. Hard to believe ''i know''.
    The drive seems fine has the...
  10. Replies
    10
    Views
    4,697

    Re: Hurco BMC40 Hard Drive Replace

    Thanks Bloke for the reply, What would you recommend? To go into detail, when i turn on the machine it boots to show bios version, then tries to load but throws up the message Missing Hurco.LDR.
    I...
  11. Replies
    10
    Views
    4,697

    Re: Hurco BMC40 Hard Drive Replace

    Thanks guys but to reword my question. my hurco hard drive in my BMC40 is corrupted, I happen to know someone with a BMC 50 machine running ultimax3 which is out of use. will the hard drive from the...
  12. Replies
    10
    Views
    4,697

    Hurco BMC40 Hard Drive Replace

    Hi,
    Quick questions for any of you hurco heads.
    Have a corrupted hard drive for a bmc40 running ultimax 3.
    Is it possible to replace it with a hard drive from a bmc 50 or would i run into any...
  13. Replies
    33
    Views
    15,852

    Re: Bad Hard Drive

    Hi,
    Have a BMC 40 late 80's early 90's with ultimax2 on it, hard drive seems to be knackered, as we have been told. the left data screen boots to bios then knocks off. the screen is fine as we have...
  14. Solidcam ultimax Vm1 Hurco Post Processer needed

    Hi
    First time poster, really stuck here, spent a heap on solidcam software and a 2nd hand VM1 with ultimax software,
    No dxf, and just a pain because im used to cam, iv contacted solidcam for...
Results 1 to 14 of 14