584,841 active members*
4,684 visitors online*
Register for free
Login

Search:

Type: Posts; User: alivexx1

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,254

    Re: okuma lr 15 cpu alarm

    This is old thread, but I had similar problem before, and I had to change out MB1 and MB2 boards, then re-install all softwares and programs back into the controls....make sure to have backup...
    ...
  2. Replies
    7
    Views
    612

    Re: Background suppression proximity sensor

    If it's not going past seq 6 because of the tool unclamp LS not turning on, then you need to look at the tool unclamp LS and see if it's working or not. I have a different Okuma, but our tool unclamp...
  3. Re: Okuma 700M Memory Disk Format Error and Floppy Disk Read/Write Error

    I called Okuma in to fix it, we ended up swapping the MB1 with a new board and the tech had to reformat the disk so it could be properly read by the machine.
  4. Re: Fanuc Picture - How to Download? [Fanuc Series 35i Model B]

    I figured it out and just leaving these notes for anyone in the future for Fanuc 35i.


    On fanuc 35i model B, you hold down the two right most soft keys to enter boot mode when powering on the...
  5. Re: Fanuc Picture - How to Download? [Fanuc Series 35i Model B]

    Yeah, I already have the file open and modified on fanuc picture software. Now how do I download it into the CNC?
  6. Fanuc Picture - How to Download? [Fanuc Series 35i Model B]

    Good morning, I have modified an existing OEM custom screen using fanuc picture on my laptop. I have created a .mem file on my flash-drive. What steps do I take to download my new HMI project onto my...
  7. Replies
    2
    Views
    2,391

    Re: Okuma ER-M-SA Encoder Pinout

    Hey man, I am in need of the pinout for the exact same encoder, but I could not open the link you posted! Could you PM me the pdf of it or find a way to send to me? Thanks!!!
  8. Looking for Series 9/440 Controller + Parts Catalog

    Hello, I am looking for series 9/400 controller part #8520-4S5A-BAT-EX4-Y-1-2-3-4-5. Does anyone have this or suitable replacement.?

    Most importantly, I am searching for the parts catalog, so I...
  9. Re: Down Okuma LU300, P200L - Does anyone have these CD files

    I found the CD #2 and installed. Our hard-drive is showing internal hard-ware fault, RAM / memory parity error. So either issue is in RAM or hard-drive. I found another hard-drive for same controls...
  10. Down Okuma LU300, P200L - Does anyone have these CD files

    Hello, I have an Okuma LU 300 with P200L controls. I need to install the osp system software, but I only have [CD 2]. Could anyone share the files for [CD 3]? That would be a great help! I would like...
  11. Replies
    8
    Views
    1,187

    Re: Searching for Manual for Okuma OSP 7000

    I found the correct manual, it's not in the maintenance manual I guess.

    I also received 1048, motor cable overcurrent. We receive this whenever we speed up the spindle motor speed, so I'm...
  12. Replies
    8
    Views
    1,187

    Re: Searching for Manual for Okuma OSP 7000

    Hello, I am now getting alarm # 1038, and again, I could not find this alarm in my manual. Does any one have any troubleshooting guide on this alarm and what to check ?

    Thanks,
  13. Re: Okuma 700M Memory Disk Format Error and Floppy Disk Read/Write Error

    I looked up the error address below DE000000 in the manual, it is pointing me towards the CMOS on MB1. Is the CMOS on the board or on the DRAM card? I have both new MB1 boards and DRAM cards, but no...
  14. Re: Okuma 700M Memory Disk Format Error and Floppy Disk Read/Write Error

    I think my Floppies are good, I am getting a red light on my Main Board 1 (MB1) under the SBER led light. I am also getting a cpu bus alarm / error on the screen. I am looking this alarm up now,...
  15. Re: Okuma 700M Memory Disk Format Error and Floppy Disk Read/Write Error

    How can I check the health of floppy disk? Am I able to plug the floppy disk into a different PC or can this only be read through the floppy drive on the Okuma?
  16. Re: Okuma 700M Memory Disk Format Error and Floppy Disk Read/Write Error

    Right, but where does the issue lie if I have changed out the FR board, the cable from FR board to floppy disk drive, and the floppy disk drive itself? If I have changed out all 3 of these with known...
  17. Okuma 700M Memory Disk Format Error and Floppy Disk Read/Write Error

    Good morning all,

    I have an issue with my Okuma 700M, MX-45. I need to re-install software because I am getting "128 Memory Disk Format ERROR"; when I plug in the first floppy disk and flip on...
  18. Looking for OSP-P200L Okuma Keyboard (Board #00780)

    Hello to all,

    Does anyone have a working Okuma Keyboard from an OSP-P200L they are selling or know where I can buy from? My local Okuma Distributor does not carry either. Please see attached...
  19. Replies
    7
    Views
    1,611

    Re: LU300 Tool Offset Page

    Hahaha Deadly Kitten, you are so funny. Even in your username, you are an animal hahaha.

    I have not had the chance to try out your methods. They are still just pushing the squishy button and...
  20. Replies
    7
    Views
    1,611

    Re: LU300 Tool Offset Page

    #2 Installation did not work, it keeps saying "the folder path 'Program Files' contains an invalid character. Any way to fix this? Or please show me your last trick.
  21. Replies
    7
    Views
    1,611

    Re: LU300 Tool Offset Page

    Deadlykitten, Your Post looks very promising.

    1) Yes, we took off the button and pushed the squishy thing behind it. It does work, but after 100 or so presses. Overtime, I am positive this method...
  22. Replies
    7
    Views
    1,611

    LU300 Tool Offset Page

    I have a LU300 Okuma with OSP-P200L control; our tool offset page button is not working and we cannot run without it. Is there any way to access this page without pressing that button? Perhaps a...
  23. Replies
    8
    Views
    1,187

    Searching for Manual for Okuma OSP 7000

    Good afternoon,

    I have an Okuma OSP 7000 and I'm searching for a manual that has alarm codes along with descriptions on how to troubleshoot the specific alarm. For example, I am getting 2832...
  24. Replies
    2
    Views
    3,350

    Re: Allen Bradley Kinetix 300, E19 Servo Fault

    Motor Model: Rockwell automation, MPL-B320P
  25. Replies
    2
    Views
    3,350

    Allen Bradley Kinetix 300, E19 Servo Fault

    Good afternoon,

    I am receiving the E19 Servo fault on the Allen Bradley Kinetix 300, as seen in the link below (I cannot find out where to upload a picture, sorry). The manual states this as an...
Results 1 to 25 of 25