584,846 active members*
4,636 visitors online*
Register for free
Login

Search:

Type: Posts; User: djr76

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: Is there a M-code controllable 110v outlet on the Haas?

    Find a 110 power source in the cabinet, run the red to one side of pump, the other wire from pump to n.o on spare m code relay, run white side of power source to common. I have air solenoids that...
  2. Replies
    4
    Views
    921

    Re: GWizard default surface speeds

    Ive never used GWizard, but my guess with the slider turning from green to yellow means youre pushing the tool outside optimal cutting conditions. I use this calc micro100.hsmadvisor dot com, you...
  3. Replies
    4
    Views
    921

    Re: GWizard default surface speeds

    Are these values for dynamic milling (high efficiency) with chip thinning in mind? HSMadvisor spit out these numbers for 6061 at 1.5" depth, 3/4 carbide. 10k rpm 1962 sfm, 280 ipm. I think Bobs...
  4. Re: Is HSM Option Needed to run Fusion 3D Tool Paths

    The tool path can get quite jerky when going at a high feed rate without having that look ahead feature turned on. I've never used Fusion but in Mastercam, you can mitigate that issue somewhat with...
  5. Replies
    1
    Views
    506

    Re: ST-10, Restricting Turret

    I plumbed air into the coolant supply line after the ball valve and use the spare M code relays to wire in a solenoid valve. So when I want to use air, I close the ball valve so it doesn't back feed...
  6. Re: How to make/cut an inner guide on aluminium pipe - suggestions

    Look into broaching.
  7. Re: Need some advise on an efficient way to get stock level in a vise

    You could be getting jaw lift if its a cheap vise, or you're clamping above the jaw plate line (taller jaws than the jaw plate) which can cause jaw lift as well. Using a torque wrench to get...
  8. Replies
    3
    Views
    974

    Re: Cutting Alum. stock

    You can always have your metal supplier quote your stock with saw cutting, typically it doesn't cost much for an value added service like that.
  9. Replies
    2
    Views
    740

    Re: Vertical Mill or Enclosed Tormach

    I would go with the enclosed tormach over a knee mill. Have you looked into a used haas?
  10. Re: How to set offset correctly to mill threads with cutter comp on

    I program with comp on and just adjust the tool size.
  11. Replies
    1
    Views
    697

    Re: New haas vf2ss metric/english issue

    Did you call your HFO? Typically they setup and calibrate the probe on installs. I bought a VF8 that was preinstalled and calibrated at the factory.
  12. Replies
    12
    Views
    3,289

    Re: Probe - Diameter Message

    By Studying the Renishaw Inspection + manual, an add on to Mastercam, or Renishaw has a number of software to generate and export data.
  13. Replies
    3
    Views
    1,618

    Re: VF3 power failure alarm

    I would google Haas Australia and call the closet hfo near you and talk with tech support.
  14. Replies
    2
    Views
    648

    Re: General quesion on Haas VMCs

    VF0 26X14
    VF1 26X14
    VF2 36X14

    You can find all the specs at haascnc
  15. Replies
    2
    Views
    1,395

    Re: Hass service engineer

    Haas Automation Ltd - Headquarters - Norwich
    Haas Automation Ltd
    Convent Road
    Norwich
    NR2 1PA
    Telephone: 01603 760539
    Fax: 01603 760542

    Email Sales: [email protected]
    Email Service:...
  16. Replies
    1
    Views
    677

    Re: skip block in haas

    You mean this --------> /

    add it in front to what ever block you want to skip.

    or if you want to skip a bunch of blocks

    /M99 P100

    Blocks you want to skip
  17. Replies
    13
    Views
    3,653

    Re: Haas standard coolant filter

    Try McMaster Carr and type in "water filters" in the search field.
  18. Replies
    2
    Views
    556

    Re: Coating Parallels

    You can room temp black oxide 65-85F. Your vendor should be able to confirm whether or not it will warp though.
  19. Replies
    2
    Views
    626

    Re: Need tapping advice

    Scientific Cutting tools, Inc, has a thread mill G code generator.
  20. Re: Haas DS30 Y BMT Turret Bearing Failure Due To Rust After 7 Months ???

    I would fight Haas and HFO tooth and nail over this, coolant shouldnt be mixing with grease.
  21. Replies
    8
    Views
    3,212

    Re: Why does my 303 part warp?

    I machine 303 all the time. Just straighten it in an arbor press.
  22. Replies
    2
    Views
    826

    Re: HAAS VF7 Program "Jumping"

    Does it only do it with the one program "B" and no others if "A' is running? If so, have you tried renaming the program(s)?
  23. Replies
    4
    Views
    1,147

    Re: Help with 17-4 PH

    Is your depth of cut greater than the radius of the insert tip? Did you try pushing your feed rate harder?
  24. Thread: HAAS MDI

    by djr76
    Replies
    3
    Views
    1,067

    Re: HAAS MDI

    in mdi, hit erase program to delete whats stored there.
  25. Replies
    7
    Views
    3,458

    Re: HAAS DS30-SSY with M97 Looping

    Set the Insert that is cutting the bore into another tool offset. Then call the tool with corresponding offset you set the tool to in the program.
  26. Replies
    6
    Views
    1,162

    Re: Trouble with spiral flute taps

    OSG Hypro NRT list 14001. I just did a job thread forming 10-24 X 1" deep in aluminum, did 3000 holes with 1 tap.
  27. Replies
    1
    Views
    772

    Re: Haas vf 2 chip chute wanted

    $495.00 in the Haas parts store.
  28. Replies
    1
    Views
    950

    Re: New Haas serial engraving macro location

    Macro #599 or I think #10599 NGC
  29. Replies
    5
    Views
    1,556

    Re: Chatter - I am lost for ideas please help

    Carbide or heavy metal bore bar? What kind of bushing, split, slotted? Does your machine have variable spindle speed? If you have facebook, the group called "Machinist" with 112K members have a...
  30. Replies
    4
    Views
    955

    Re: made an account just to ask some experts...

    Did you try browsing the denford website? Specialists in Technology for Education - Denford Ltd
Results 1 to 30 of 481
Page 1 of 17 1 2 3 4