584,871 active members*
5,427 visitors online*
Register for free
Login

Search:

Type: Posts; User: botha.y

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    3,291

    Re: Pulse Generator Quit Working

    Would you happen to have another fanuc MPG that you could connect to your machine, I'd say that would be a quicker way to get your answer straight away.
  2. Re: NEED HELP PLEASE WITH MELDAS 500, TYPE FCA-520 AMR

    That would be
    LED display Ab:
    Symptom: Initial communication with the NC was not carried out.

    Cause of occurrence 1: The axis is not used, or is set to disabled.
    Investigation method: Is the...
  3. Thread: 0-md alarms

    by botha.y
    Replies
    2
    Views
    1,526

    Re: 0-md alarms

    Change your battery and load back your backups (parameters, pmc parameters and macro programs).

    Tell us if it was only that.
  4. Re: Fanuc Oi-T removed battery with power off, now code 351 alarm

    You could reload you parameters from a parameter text file, your programs from a programs text file, and finally your diagnostics from a diagnostic backup text file, this might be enough to solve...
  5. Re: Fanuc Oi-T removed battery with power off, now code 351 alarm

    Reload your RAM backup.
    Insert your PCIMA card into the slot with the RAM backup.
    While booting, press the two right-most menu keys.
    Select 7. SRAM data backup.
    Then select 2. SRAM restore....
  6. Thread: Fanuc 0i FTP

    by botha.y
    Replies
    0
    Views
    3,486

    Fanuc 0i FTP

    Hi guys,

    I have the strangest issue I've ever seen. I had configured an FTP server on a computer for a 0i-MD Fanuc control. I installed a new computer and wanted to use it instead as the FTP...
  7. Replies
    2
    Views
    1,907

    Re: Fanuc O-M on SuperMax Max3 - Not Ready Issue

    Press and release EMG stop, I have a 0-MC control on a Feeler machine that requires you to do that. Else check your emg stop line as a whole, might be that too.
  8. Replies
    6
    Views
    31,086

    Re: 750 Serial spindle link error

    Ah yes even if it's unlikely the problem you might as well check the three phase voltage as well as continuity about everywhere on your circuit up to the spindle motor as well as the DC link voltage....
  9. Replies
    6
    Views
    31,086

    Re: 750 Serial spindle link error

    Try swapping spindle sensor, else try swapping cable, else might be the drive.
  10. Replies
    1
    Views
    1,607

    Re: comet 750 520control

    I assume display on your screen shows:
    S01 SERVO ALARM:PR 0042 Y

    On Mitsubishi 500 series, alarm S01 alarm number 42 corresponds to:
    FE1 Feedback error 1: A feedback pulse was omitted in a...
  11. Replies
    3
    Views
    3,323

    Re: Mazatrol T32-2 G-code Program start

    Should be same syntax as the rest. To go to line N40 for example, you write:
    GOTO40;
  12. Replies
    6
    Views
    2,192

    Re: 21i MB display error?

    Ok so you tried new cable, new router, and you did follow instructions on setting your FTP server with ftpserv software with all correct IP addresses, correct?
  13. Replies
    5
    Views
    5,330

    Re: Mazak QT8N T32-2 Tool change position

    I think Mazak T32 is with Mitsubishi 300 controls, so there is an edit lock B (that's the data protect key that is on your operator panel) and edit lock C (param 39 of basic specifications is set to...
  14. Replies
    6
    Views
    2,192

    Re: 21i MB display error?

    Did you check that your ethernet cable is ok? Also, re-crimp both ends just in case. These guys made this doc:
    http://cnctechservices.ca/images/FTP%20Server%20with%20Letter%20Head.pdf
    I think that...
  15. Replies
    5
    Views
    5,330

    Re: Mazak QT8N T32-2 Tool change position

    My guess would be to check your tool change macro program, assuming your machine has always had this problem.
  16. Replies
    6
    Views
    6,103

    Re: Boot menu on Fanuc 20i

    Well you press the two buttons before, hold them, and only then you power on the machine. Since you say you couldn't get it done for 3 different machines with 3 different Fanuc i controls, must be...
  17. Replies
    6
    Views
    6,103

    Re: Boot menu on Fanuc 20i

    In the CNC menu on screen after control is loaded up, does your keypad and menu keys function properly?
  18. Replies
    6
    Views
    6,103

    Re: Boot menu on Fanuc 20i

    Boot by holding down number 6 and number 7 from keypad and see what you get.
  19. Re: Mazak QT20 T1 - Alarm 55 - Fanuc spindle drive overload

    PM MrMazak in this forum, he would know more about which I/O card with analog output to purchase for this control than I would.
  20. Replies
    9
    Views
    2,404

    Re: Makino with Fanuc controls issue

    Does your machine slow down when it hits the dog during reference return?
  21. Thread: MAZAK QT10

    by botha.y
    Replies
    1
    Views
    1,108

    Re: MAZAK QT10

    Start by checking the voltage input to your machine at all points and see if all is ok. Careful for deadly electrical shocks there.
  22. Replies
    1
    Views
    814

    Re: M700V with analog spindle drive

    Alright so now I got the Mitsubishi side and Mentor II Analog drive side to work, though there is still quite some adjustments to be done later on. Analog spindle params setting for M700V is pretty...
  23. Re: Mazak QT20 T1 - Alarm 55 - Fanuc spindle drive overload

    I do think you have a spindle load meter on your screen, what does it say when you turn your spindle for a couple minutes at all different gears and different speeds, check the load behavior. Very...
  24. Replies
    2
    Views
    3,795

    Re: mazatrol 640m thread milling

    6.13 Spiral Interpolation; G02.1/G03.1 (for machining centers)
    Function and purpose
    This function carries out interpolation that smoothly joins the start and end points in a spiral. This...
  25. Replies
    2
    Views
    1,421

    Re: MHP-30 Vertical Machining Center

    From a quick look, here's some pdfs for the Dynapath control:
    Index of /pdf
  26. Replies
    1
    Views
    814

    M700V with analog spindle drive

    Would anyone have a M700 or M700V control with an analog spindle drive?

    I'd just like to have the parameters list in order to use the spindle parameters as template for a retrofit I'm doing....
  27. Re: Need some brainstorming on sluggish M700V control for retrofit

    Just as information, that G018 cable was the cause of the issue and was replaced by a new one last week. Cheers.
  28. Re: Northwood Fanuc 21i-M - Multi-Drill Spindle and pcmcia memory reader

    You might be using a card that's too big I'm not sure what's the upper limit. I always use IGT 40MB PCMCIA cards like these:
    SDP3B 40MB PCMCIA ATA Flash Card | eBay Also use your Fanuc control to...
  29. Replies
    1
    Views
    2,901

    Re: GE FANUC 15TTB 'START REJECTED' Messsage

    START REJECT
    The start of automatic operation is not accepted.
    (1)Automatic operation pause signal *SP is low.
    (2)An alarm exists.
    (3)The SRN signal has been sent.
    (4)The program the operator...
  30. Replies
    4
    Views
    1,219

    Re: Soft button "LARGE" on Meldas 500

    The instruction manual says:
    In large-size mode, data search and program creation are enabled.
    The FILE menu is not available; refer to the data input/output program list
    to check the stored...
Results 1 to 30 of 349
Page 1 of 12 1 2 3 4