Hi PCW_Mesa
Pulled the Interface card and reinstalled. Also checked remaining connections. Computer now boots up fine into Pathpilot.
Obviously this computer doesn't like to sit. I'm sure...
Type: Posts; User: Willyb
Hi PCW_Mesa
Pulled the Interface card and reinstalled. Also checked remaining connections. Computer now boots up fine into Pathpilot.
Obviously this computer doesn't like to sit. I'm sure...
Hi Guys
What are you Guys using in your DIY Fog Blasters (FB)? Anyone using a Flood Coolant Mix? I would think it should work fine. When I get around to building my FB, I want to be able to use...
GITERDUN
Check your private messages.
Hi Guys
I have been looking into Near Dry Machining (NDM) for use on my PCNC1100. Up to this point I have been using a Full Flow Coolant setup along with it's associated problems. (Messy,...
Hi BIG IGG
You can tell by the Serial Number.
Series I - 1 to 1325
Series II - 1326 to 1999
Series III - 2000+
Hope this helps.
Hi Guys
There is room for the LED Light below the Duality Lathe's small tool post plate. This Light is very easy to Re: & Re: loosen a couple of Wing Bolts and it slides right off the Spindle...
Hi Frederic
Here are a couple pictures of the Princess Auto LED Light installed on my PCNC 1100. (Sorry the Lathe happened to be mounted) I don't have a Tool Changer but I don't think there would...
Hi Frederic
I will post some pictures of this LED Light installed on my PCNC1100 this afternoon.
willy
Hi Steve
I find this light works very well. Really brightens up the area under your Spindle. Unless your shop is very well illuminated, (not like mine) the addition of this light will be an...
Hi Guys
Just wanted to let you guys know about a great LED Light that I am using for a Spindle Light on my PCNC 1100. It fits over the nose of your Spindle and is held in place with three Wing...
Hi Guys
Not to sure if this is the correct place for this question, but here goes.
If you where designing a Vacuum Engine (Flame Sucker) using a 4.5" Flywheel with a face width of 1/2" wide...
Thanks Rob.
Hi Guys
I am planning on building a CNC Plasma Table and have some questions on it's design. I am planning to weld up the frame out of tubular steel. For the X axis I will likely use a set of...
(1) Metal Way Covers.
(2) Economy Probe & Tool Setter.
(3) Simple Tool Changer. (A few Tools on end of Mill Table)
Hi Guys
Does anyone know what the difference is between the two Post Processors that BobCad offers for the Tormach PCNC-1100 cnc Mill?
Willy
Hi Legion99999
It's been 15 months and no word. Did Smith ever make good on the junk they sold you? Did they ever come and fix all the problems with the CNC Lathe?
Willy
Hi Randy
Mine takes about a minute to completely retract. The first quarter of it's travel moves rather quickly which I assume is air being purged out of the Ball Nuts and passage ways. The...
I have the same setup as Karl. A Belt Skimmer and Aerator, both on a Timer. Seems to keep the Coolant nice and fresh.
Willy
Hi Legion99999
So what's the story? It's been almost 6 months since you received your Lathe. Did they ever come and take it back for repairs like they said they were going to? I am sure there...
Hi Chris
Lets see some Videos of your machines working. Machining Aluminum and Steel.
Willy
Come on Guys, this is a Tormach Forum and now we have two non Tormach manufactures plugging their products here. It's one thing to have Chris post about his new purchase, but now we have to listen...
Hi Guys
Being as Chris has now purchased a Mikini Mill, this thread should be moved to it's own forum for any further conversations on this product. I am not interested in reading about non...
Hi Guys
In the Video of it machining plastic, the Spindle Motor sounds like it is working harder than it should be for the material? I am also wondering why there are no Videos of it machining...
Hi Guys
Looking for help with designing and building a Mixer for a model Hit & Miss Engine that I am building. The engine is a 1/7th scale of a 7hp Perkins Wind Mill Company. I understand from...
Hi Legion99999
Tell them you want your money back and to come and pickup up their junk. How could you ever be assured that they would repair it properly?
Very nice Stand. You have built a good looking CNC mill. Keep up the good work.
Willy
Great job designing and building your CNC Lathe. Can't wait to see this machine in action. Keep of the good work.
Willy
Hi Legion99999
Sorry to hear that. I was thinking that their customer service had improved? Guess not. I found out a long time ago about Smithy's customer service. I was in the market for a...
Hi Guys
I ordered my Duality Lathe on May 5 and it arrived safe and sound (Fedex) on May 11 to Ontario, Canada. It was in good shape and well packaged. First of all the Lathe is placed inside a...
Hi Guys
As long as the VFD is Fused correctly, are there any issues using a 230 Volt, 4.5 A, 3 Phase Motor with a 200 - 240 Volt, 8.0 A, 3 Phase VFD? The Motor should only draw it's rated currant...