I have the same machine and control. And trying to learn to operate the control. However, in the manual mode and if you get to the m code input and press help it will give a list of m codes. Mine was...
Type: Posts; User: TheDeon
I have the same machine and control. And trying to learn to operate the control. However, in the manual mode and if you get to the m code input and press help it will give a list of m codes. Mine was...
I just acquired the VMC with the manuals. Not familiar with a VMC and a Heidenhain control. There is no videos for BP with TNC370 to learn from. Is there anyone out there who would be will to...
I just acquired the VMC with the manuals. Not familiar with a VMC and a Heidenhain control. There is no videos for BP with TNC370 to learn from. Is there anyone out there who would be will to assist...
It worked. Terminals 1 fwd and 13A rev. Terminals 2 and 5 and 11. was also used on the VFD. 300 rpm on high pulley pulled 6.5hz and 4500 rpm pulled 80hz. About 3100 rpm wad 60hz. So Thank You,...
I'll Give it a try. Thank You
I've installed a haugyang with a 3ph air compressor and it works good. But I'm in the process of retrofitting my mill with a centroid acorn controller. The motor is a leeson 2hp 3ph. the VFD is a...
Does anyone have one that works with autodesk products. It’s supposed to be basic fanuc. You can go there website for further info.
Yes I had to assume it would need to make a circuit. So, 5V Out to switch and from other terminal on switch to 5V IN. When compressor hits 120psi it turns off. When tank hits 90psi it turns on.
...
Hurray, I got it figured out. And I want to thank those that gave advise and replies to help solve the problem.
So here is the way that a Properly sized VFD will work with an air...
Finally some pictures of the manual and the air compressor. The power plug goes the the socket next to the breaker box which is wired to the VFD, Which is wired directly to the motor. The pressure...
http://www.cnczone.com/forums/attachment.php?attachmentid=376578&stc=1http://www.cnczone.com/forums/attachment.php?attachmentid=376580&stc=1http://www.cnczone.com/forums/attachment.php?attachmentid=37...
I could but the question is. The motor is wired directly to the VFD. There is a pressure switch that has contacts that will allow the compressor to run if below 120psi. Can i wire that into the VFD...
All is programed in. Does not stop at 120psi. I have to stop VFD manually.
Ok. Will give that a try. Here are the setting as of now. But where do I hook up the wires on the VFD and for the contact switch on the compressor to get it to shut off at 120psi and restart at...
Well I don't have a PD141 or higher then PD35. It goes from Pn1 thru Pn35. It only has 1 buss terminal row. 12v out, 5v out, 5v in, 10v in, 20mA in,5v Fout, GND, FWD, REV, RST, DO+, D1-, D2 Jog,...
Well I took some pictures of my manual and wrote down the setting on the VFD. But it ain't letting me find them to post them.
I have no link to the video. But search VFD running an air compressor. I'm not sure what parameters I should/could use and what to set them at. I have it set to 60hz as far as parameters go. Not...
Thanks for your replys. HY04D023VFD. The air compressor does have an unloader valve. The video on youtube didn't specify any settings programmed into the VFD.
I have an air compressor with a 3ph 3hp motor. I bought the proper size VFD to power it. I really know nothing about programing the VFD. However, I wired it using the magnetic starter and it...
I have the whb04b-6 and need the plugin for uccnc
Al,
I think that would do it. But, would it be capable for Ridged Tapping? I run across a lot of discarded treadmills all the time.
Deon
Hello Everyone,
I'm kinda new at this stuff. And I have 5400 CNC Mill. I would like a bit more spindle power and speed. What would be my options?
I would like to be able to do the following:...
I looks Nice. Did it work out ok? You have not let us know yet.
Cool
Thank You
Deon
Squirrel,
I downloaded the .rar file. What opens it to read the read me txt?
Sorry to ask
Thanks
Deon
Thanks guys,
Squirrel do you have instructions for what I need to do? I'm kinda new at this.
Deon
Hi all,
It's my first post and need some help.
I'm trying to use the probing plugin in mach3.
I have done many test but I always get "previous SEQ not yet complete"
it will move the x axis...