584,846 active members*
4,118 visitors online*
Register for free
Login

Search:

Type: Posts; User: pero81

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    1,153

    SK-66B-KC tool setter wiring

    Hello all,

    i've purchased this chinese tool height setter:
    ...
  2. Replies
    33
    Views
    2,758

    Hi Chris, my working area is 2,5m in X axis and...

    Hi Chris, my working area is 2,5m in X axis and 1,5m in Y axis. I have set max speed at 30m/min ( 1180 IPM). I can go up to 40m/min (1575 IPM) but I don't need that much speed. About USB SS I have...
  3. Replies
    33
    Views
    2,758

    Hi Chris, I've installed ethernet smooth...

    Hi Chris,

    I've installed ethernet smooth stepper with C32 board on my machine. I can without problems jog machine at 30m/min with X and Y axis. I'm using rack and pinion with servo motors and 10:1...
  4. Thread: Artcam rapids

    by pero81
    Replies
    11
    Views
    2,097

    I use Artcam 8 pro. Peter

    I use Artcam 8 pro.

    Peter
  5. Thread: Artcam rapids

    by pero81
    Replies
    11
    Views
    2,097

    Mach3 mm post Peter

    Mach3 mm post

    Peter
  6. Thread: Artcam rapids

    by pero81
    Replies
    11
    Views
    2,097

    Here is post and manual for editing if it will be...

    Here is post and manual for editing if it will be in any help.

    Peter
  7. Thread: Artcam rapids

    by pero81
    Replies
    11
    Views
    2,097

    Hi ger21, I've tried this and when I open artcam...

    Hi ger21, I've tried this and when I open artcam it gives me error message:

    duplicate statement found Line 53 FIRST_RAPID_RATE_MOVE = "[N] G0 Z30.00"

    Peter
  8. Thread: Artcam rapids

    by pero81
    Replies
    11
    Views
    2,097

    Hi Mike, the reason is that I use a lot of...

    Hi Mike, the reason is that I use a lot of programs and if you use different dia of tools you must recalculate toolpaths. I just don't have time to edit code every time.

    Peter
  9. Thread: Artcam rapids

    by pero81
    Replies
    11
    Views
    2,097

    Artcam rapids

    Hello, I have a problem with my artcam post and I can't figure out how to change it to do what I want. I want in the begining of the file first rapid speed on X and Y and then with Z.

    This is how...
  10. Thread: Servo motor

    by pero81
    Replies
    2
    Views
    240

    Thanks for answer Al. I have sent motor back to...

    Thanks for answer Al. I have sent motor back to factory and I hope they will sent me new one.

    Peter
  11. Thread: Servo motor

    by pero81
    Replies
    2
    Views
    240

    Servo motor

    Hello,

    I have a problem with one of my ac servo motor and I need someone to tell me what could be wrong. Now on to the problem. I purchased 4 new sets of servo motor and drives. When I recieved...
  12. Replies
    5
    Views
    798

    Hello Matt, I think I've tried everything I can...

    Hello Matt, I think I've tried everything I can think of. I realy dont know what else to do. I will probably start thinking to buy some better drives and motors because of this problem and bad...
  13. Replies
    5
    Views
    798

    Thank you very much for answer Alan. It's 5V,...

    Thank you very much for answer Alan. It's 5V, 2500PPR quadrature encoder. It is original encoder. I even took all motors to service company to make sure that all signals are working and if the...
  14. Replies
    5
    Views
    798

    Anybody please? Peter

    Anybody please?

    Peter
  15. Replies
    5
    Views
    798

    Servo velocity control mode

    Hello all, I have a problem with my servo and hope someone can help me. First of all let me introduce my system. I use Mach3 with DSPMC/IP motion controller and servo drive (sidc650) with motor...
  16. Replies
    8
    Views
    330

    Thank you very much. Will try that and report....

    Thank you very much. Will try that and report. Thanks.

    Peter
  17. Replies
    8
    Views
    330

    Hello all, I need some help again. At the end I...

    Hello all, I need some help again. At the end I didn't replace the encoder because it works just fine. Now I have some other problem. Now the encoder is not positioned properly because it was took...
  18. Replies
    8
    Views
    330

    Ok I tried one of your metod and it worked. I was...

    Ok I tried one of your metod and it worked. I was using a meter with one cable on minus and the other cable of the meter on the U pulse. The voltage went high (5v) 4 times in one motor revolution....
  19. Replies
    8
    Views
    330

    Ok thanks. Will try that and report. Peter

    Ok thanks. Will try that and report.

    Peter
  20. Replies
    8
    Views
    330

    Thanks for reply. Please let me know how do I...

    Thanks for reply. Please let me know how do I look how many poles motor have. Servo shaft dia is 8mm.

    Peter
  21. Replies
    8
    Views
    330

    Need new encoder

    Hello,
    I need to replace encoder on the servo motor. I have contacted original manufacturer but didn't get any answer so I'm turning to you guys for help. I have attached two pictures of the...
  22. Replies
    112
    Views
    4,368

    In what operation mode are you running those...

    In what operation mode are you running those servos?
  23. Thread: Artcam g41/g42

    by pero81
    Replies
    2
    Views
    1,007

    Anyone please?

    Anyone please?
  24. Thread: Artcam g41/g42

    by pero81
    Replies
    2
    Views
    1,007

    Artcam g41/g42

    Hello, can someone please tell me how to add g41 and g42 moves into artcam post for mach3.
  25. Replies
    112
    Views
    4,368

    I have one question. I have atc spindle with two...

    I have one question. I have atc spindle with two air connections for piston to release or clamp tool and one for taper clean. On first one it says piston delivery, on the second one piston retract on...
  26. Replies
    112
    Views
    4,368

    so the z-axis brake is used only when the machine...

    so the z-axis brake is used only when the machine is powered off?
  27. Replies
    112
    Views
    4,368

    Can you please tell me how your z-axis...

    Can you please tell me how your z-axis counterbalance works, and why are you using z-axis servo brake?
  28. Replies
    112
    Views
    4,368

    Are you still using Mach3?

    Are you still using Mach3?
  29. Replies
    112
    Views
    4,368

    It is seen from the photo that you are not using...

    It is seen from the photo that you are not using smoothstepper. Why?
  30. Replies
    112
    Views
    4,368

    .

    .
Results 1 to 30 of 37
Page 1 of 2 1 2