hi everyone
i need information for inverter replace
Which model of Yaskawa inverter has the ability to replace Baldor inverter with Ridgid tapping?
If possible, is there a wiring diagram for it? ...
Type: Posts; User: Mhook
hi everyone
i need information for inverter replace
Which model of Yaskawa inverter has the ability to replace Baldor inverter with Ridgid tapping?
If possible, is there a wiring diagram for it? ...
Fadal uses rk5 time delay fuse (5 amps or 10 amps) under Baldor inverter for 13 ohm brake resistor
is it possible to use mcb for example 5 amps mcb?
hi
Please, if possible, send a picture of the signal wire on the amplifier
picture of (bypassed the velocity loop and soldered signal wire directly into a specific point in the amplifier farther...
hi everyone
I read somewhere that Fadal dc amplifiers have 2 modes, velocity and torque mode, and that in velocity mode we need Tach feedback, is there a way to keep these amplifiers and change to...
Hello friends
how many millivolts of Ac ripples allowed in the Fadal power supply at 5v and 12v !?
i have 220mv ac ripples in 5v and +12v
and 15mv in -12vdc
Is this voltage correct?
Thank you, you have a lot of information
hi everyone
What is the exact function of this part and how can it be tested?
And why is it placed after the dc amplifier?
What was the need to use this transformer in the circuit?
As far as I remember, the vmc15 xt ballscrew had a diameter of 32 mm and inch pitch equal to 5.5 mm.
check power supply voltage
12v and 5v
input 120v ac
check jumpers on transformer for correct output voltage
check blue capacitor voltage between 125to160
vdc depend on type of transformer
check...
Thank you for the good information
you are right
Hi everyone
I replaced the old crt monitor with a new one lcd ( fadal vmc15 1995)
But the color of the letters is white
Is there a way to change the color to green?
please check your email
!?
my control is seicos ii
hi everyone
how can i change vm40ii seicos language german to english?!
thx
It makes no difference!
In addition, Fadal's eprom program is wrong. The correct number for the metric ballscrew is 595 ! not 302
thx a lot
hi
all axis balance between 0-1
Which parameter is there for axis lag in setp?
Hi friends,
I have a big problem, the quality of the surface finish at 45 degrees is extremely bad, the resolvers and tachos are new , but apparently the axis numbers become similar with a delay...
hi
today I use silver graphite with a combination of 80% silver and 20% graphite and the quality of the signal was much better than Fadal orginal brushes. And the quality of the surface finishing...
hi everyone
What is the best type of carbon brush for glentek motor Tacho on Fadal?
1-carbon graphite brush
2-silver graphite brush
Which type provides the least amount of wear and the best...
??????
None of your business. How much SENT I posts? Are you the owner of this website?
THX!!!!!!!!
Solidcam = give me money ! give me money ! more and more !!
Nothing positive comes from all these Websites!!
Except that the employees themselves post advertisements for Solidcam !!!!
hi
I use Powermill for the 3 axis machining and sometimes 4 axis at the same time, as well as nx and hsmworks for 4 axis Fadal
i edit post processor for 4axis
Forget Fadal forever unless you don't value your money! Go for Japanese cnc!
Fadal has a simple control to learn, but it is pure cancer!!! The service requires a lot of maintenance
When you...
Yes, the thrust bearing is very important. I checked it and about 5 microns
Thank you for your answer, but I checked all this, in format 2, the g8 code is active by default, the machining speed of the machine when the program is sent with CIMCO is great, and I have no...
Hi friends
i have a vmc 4020 with dc motors and 88hs which is a boxway. When I run 2D machining, the surface quality is excellent, but when I run 3D machining, the quality is a disaster. All the...