509,652 active members
3,430 visitors online
Register for free
Login

Search:

Type: Posts; User: mactec54

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    107
    Views
    2,448

    Re: 60" x 40" new build

    The 1/2Hp motor is not going to do a very good job on a 30 Taper spindle this normally would have a 3Hp motor on it I don't know why they sold it like this
  2. Re: How to show Rpm instead of frequency? FVD yl620-a

    Set it back to the default=0 and try the DISP again I'm not a fan of this VFD Drive as many users have had problems with them
  3. Re: How to show Rpm instead of frequency? FVD yl620-a

    The DISP should select the RPM, just Press it until the RPM led is on then it will show the RPM

    You could try P00.24=9 this will give you all the options
  4. Replies
    6
    Views
    11

    Re: Mach 3, g28 safe travels height

    Just remove the G28G91 This has no place at the beginning of any program

    And try it like this G0Z0. this should go to your machine Home Zero

    Do you Home the Machine Before you setup your work...
  5. Replies
    61
    Views
    330

    Re: Need help please

    The VFD Drive should be in the Box just as you have built it, anyone that says different does not know what they are talking about, there will always be naysayers that are not capable of building...
  6. Replies
    6
    Views
    11

    Re: Mach 3, g28 safe travels height

    No code attached Just Cut Paste the code, a G28 can be a problem You don't need to use a G28 in any program
  7. Replies
    2
    Views
    4

    Re: Syntec 6MB soft limits

    G54 is your work offset or Start Position X0 Y0 Start Position, when you do you cad / cam program you should set up a frame around your job that is where the soft limits are activated, then you would...
  8. Replies
    107
    Views
    2,448

    Re: 60" x 40" new build

    Normally for low voltage it is connected Delta, this is not a very good motor being 110v don't expect it to have a very good performance if anyone else is buying this make sure it has a 220v/240v 3Hp...
  9. Replies
    16
    Views
    23

    Re: Huanyang 2.2 spindle VFD control

    Post a photo of your wiring

    First check the outputs of the Breakout Board with your meter

    Points to check with your meter 0-10v output from the Breakout board first do a M3S12000 in MDI if...
  10. Replies
    4
    Views
    66

    Re: Laguna Vs Shopsabre vs?

    The post processor is non existent because it mostly will run industry standard G-Code Format

    Here is the G-codes that your control can use, your postprocessor just needs to be changed to suit...
  11. Replies
    4
    Views
    66

    Re: Laguna Vs Shopsabre vs?

    Newcnc https://newcnc.com/cnc-routers/ is worth a look it should be easy to sort out what codes your control likes and does not like Syntec control is a good control, you just have to correct the...
  12. Replies
    16
    Views
    23

    Re: Huanyang 2.2 spindle VFD control

    Yes the jumper should be on VI for 0-10v control or Pin (1 -2 )
  13. Replies
    107
    Views
    2,448

    Re: 60" x 40" new build

    At what voltage it looks like a 3Ph motor is it 220/240 if so a simple VFD Drive will get you going
  14. Replies
    3
    Views
    21

    Re: Linear Rail Mounting method

    Correct it is better if you machine a shoulder for the rail alignment, 2mm is normal but check with your rail you are going to use as the Ground mounting edge are different heights and you need...
  15. Replies
    16
    Views
    23

    Re: Huanyang 2.2 spindle VFD control

    Are you trying to control the VFD with the Pot or are you trying to control the speed with your control software

    What are all the VFD Parameter settings you have set
  16. Re: New Machine Build - Massive CNC router for timber components

    No stress from not welding this is great, but how do you stress relieve the steel parts once it is all glued and bolted together, all the steel parts have stress from it's manufacture, just gluing...
  17. Replies
    3
    Views
    21

    Re: Linear Rail Mounting method

    Looks like it could be an improvement over just mounting direct to the extrusion, there are some that supply a machined extrusion also which makes for better mounting, any kind of mounting on an...
  18. Re: DMM DYN4 Wiring Fault Alarm to Breakout Board

    I would try what I said first uncoil the cables taking them outside the cabinet, even just try one and see if it has any affect, if not then a shorter cable is not going to fix what ever is happening...
  19. Replies
    107
    Views
    2,448

    Re: 60" x 40" new build

    If the motor is 3Ph then you could use a VFD Drive and change the speeds if could run at
  20. Replies
    0
    Views
    23

    Re: Zenbot 4848 & cutting aluminum

    You can cut mill aluminum with anything even a dremal, it how well a machine like this will work both machines are lightweight and not really suitable for milling aluminum, if you want any kind of...
  21. Re: DMM DYN4 Wiring Fault Alarm to Breakout Board

    How much extra

    I make the cable the correct length, this has to be done right or you can have a lot of more problems that could be worse than what you have now, yes coiled up is not a good Idea,...
  22. Re: DMM DYN4 Wiring Fault Alarm to Breakout Board

    You have some problem in your wiring or Turning if you can feel anything, the motors should be still with no movement at all, check the encoder cables
  23. Re: New Machine Build - Massive CNC router for timber components

    I would like to see one that has a 16"/ 20" Z axes travel and the Z axes is working at the end of it's travel 5" and doing aerospace work, I have worked in this manufacturing industry and have never...
  24. Re: DMM DYN4 Wiring Fault Alarm to Breakout Board

    Are you using the recommended Power Filters for each drive, there should be no movement of the servo motors with or without Mach3 running, Check that your Grounding is all done correct also
  25. Replies
    61
    Views
    330

    Re: Need help please

    Good Grounding practice normally takes care of most problems, As a test remove your Power filter and test again
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4