584,826 active members*
5,174 visitors online*
Register for free
Login

Search:

Type: Posts; User: blakey235

Search: Search took 0.00 seconds.

  1. Thread: Fagor 800T

    by blakey235
    Replies
    4
    Views
    2,456

    Re: Error 34

    Thanks for your reply, correct answer wasted loads of time sorting that out! you would think Fagor UK would have known
    that
  2. Replies
    0
    Views
    478

    A&T power drawbar

    I have an A & T power drawbar on my Rambo 5V air motor has stopped reversing, can't pull tools into spindle, any suggestions as to reason
  3. Replies
    0
    Views
    1,538

    Fagor 800T DNC stopped working

    Hi All my Ajax Premier + Fagor 800T refuse to talk to WinDNC been working OK for 6 months or more, will not show CNC files in WinDnc says (EXPLORER GETTING CNC DIRECTORY (transmission error)) cable...
  4. Replies
    1
    Views
    919

    Protected memory

    Does anyone know how to clear protected memory message when uploading program on Fagor 800T
  5. Thread: Fagor 800T

    by blakey235
    Replies
    4
    Views
    2,456

    Re: Error 34

    Error 34 I have discovered is caused by an extra control character at the end of the file listing, move cursor to the end and backspace over it, save and re-send 99996 lovely message SENT instead of...
  6. Replies
    0
    Views
    3,956

    BOOT ERROR 0010

    I have EMCO PCMILL 155 after switching on and loading WINNC32 message comes up BOOT ERROR 0010
    Invalid settings for USB interface, anybody come across this error message, or where to find USB...
  7. Thread: Anilam 1200T

    by blakey235
    Replies
    0
    Views
    964

    Anilam 1200T

    Hi I need to now how to set tool change position on Anilam 1200 T lathe, goes back to reference point to tool change at present
    1.5 metres ever time
  8. Replies
    1
    Views
    2,777

    Re: Rambo 5v cnc milling machine

    You may get electrical drawing copies from TPH machine tools in UK e-mail [email protected] they sell RAMBO machine tools
  9. Thread: ANILAM 1100M

    by blakey235
    Replies
    0
    Views
    1,602

    ANILAM 1100M

    Does anyone know what this error message means "" Illegal address 'T' "" or does anyone have a list of Anilam messages and their meanings.
  10. Replies
    8
    Views
    4,962

    Re: Anilam 1100 Codes?

    Hi tpodgwaite, I have a Semco turret mill with 1100m working great problem is when i upload program to control, and use draw to run the program i get the message (Illegal address 'T') there is no...
  11. Replies
    26
    Views
    11,946

    Re: Anilam 1100 Controller Problem

    I have Anilam engineers e-mail in UK if you need it
  12. Replies
    26
    Views
    11,946

    Re: Anilam 1100 Controller Problem

    I have same problem, engineer linked all connectors on board with LED for limits 6 in row on left side, still get message I have to press clear 3 times, says servo delay please wait then drives come...
  13. Thread: Fagor 800T

    by blakey235
    Replies
    4
    Views
    2,456

    Fagor 800T

    Does anyone out there know what causes error 34: Strange Character, Fagor Automation give me wishy washy reasons,
    sent them program they say its OK. must be a better set of reasons for cause of...
  14. Replies
    1
    Views
    947

    removing spaces

    Anybody know how to remove spaces in program, with Code Wizard in Edgecam 12.5, or any other way with an editor
  15. Replies
    4
    Views
    3,140

    Re: Heidenhain TNC 355 BLOCKWISE PROBLEM

    The cable you are using does not work, have tried it
  16. Replies
    2
    Views
    2,503

    Re: Fagor 800T Following Error

    If you open the door to access drive cards switch on with pliers (insulated just in case!) on the left are X and Z axis drive cards the larger one is Z there should be a
    green LED on each card if...
  17. Thread: FAGOR 800T

    by blakey235
    Replies
    1
    Views
    1,821

    FAGOR 800T

    Hi anyone out there have an Edgecam V12.5 post processor for FAGOR 800T on AJAX Premier 165
  18. Replies
    1
    Views
    835

    Re: heidenehain tnc 355 system

    You have to get machine to reference first, what error message appears when you try to reference machine
  19. Replies
    1
    Views
    1,277

    no logical home position

    I have an Ajax premier lathe with 800T, the lathe works! problem the machine does not reference as all my previous lathes ie up to reference trip in Z (tailstock) and out to max Dia X on cross slide....
  20. Replies
    18
    Views
    24,152

    have you got Edgecam 12.5 post for Fagor 800T on...

    have you got Edgecam 12.5 post for Fagor 800T on AJAX premier lathe
  21. Replies
    0
    Views
    1,011

    Postprocessor Edgecam 12.5

    I need Postprocessor for Fagor 800T 0n AJAX premier teach in lathe, can't get machine to go to logical point after setting X0 Z0 and entering T01 offsets
  22. Thread: text

    by blakey235
    Replies
    7
    Views
    1,713

    text

    can somebody tell me how to create (true type) text on an arc or circle in solid modeller 12.5, also does any body out there have a post processor for the Anilam M/L control for a Harrison M250 or...
  23. Thread: blakey235

    by blakey235
    Replies
    1
    Views
    676

    blakey235

    Hi There,
    I am drowning on my first session on this site, can you tell me how
    to post a thread introducing myself, to everyone saying hello to the community, the post a thread icon...
Results 1 to 23 of 24